1/12 RC FMC XR311 Kit

Ask a question about this product

Printable version

Options

Market Price: $363.00

Our Price:

$254.10

You Save

30%

Quantity

OUT OF STOCK

Notify me when back in stock

Details


Availability	No items available
Weight	5.00 lbs
SKU	TAM58004

1/12 RC FMC XR311 Kit

Tamiya's First R/C Buggy
This is a re-release version of the 1/12 scale R/C XR311, Tamiya's first R/C model with a suspension system, which was originally released in 1977. While maintaining the basic layout of the original, this re-release version incorporates modern improvements. The injection-molded body captures the vehicle's purposeful look. Interior parts and a driver figure are included for even greater realism.

Refined Chassis Details
The 2WD duralumin chassis frame features a rear-mounted motor rear-wheel drive layout. The battery is positioned down the center of the chassis with the receiver and ESC on either side for exceptional balance. 4-wheel double wishbone suspension features upper and lower H-arms and adjustable metal torsion bar springs. Fully-enclosed gearbox may be assembled with one of three different gear ratios.

Specifications:

1/12 Scale　
Length: 400mm, Width: 168mm, Height: 139mm Wheelbase: 256mm
Weight: 1,800g　
Type 540 Motor
Rear-Wheel Drive
Tire Width/Diameter: (F/R) 29/77mm　
Tread (F/R): 138mm
Duralumin Frame Chassis　
3-Bevel Differential
2-piece Steering Tie-Rod
4-Wheel Double Wishbone Suspension with Metal Torsion Bar Springs
Gear Ratio=9.3:1, 16:1, 21:1

RCEXL Universal On Board Glow System Methanol Engine Ignition With LED Indicator

Fuel clunks are a must for aerobatic flying. It insures that fuel is always flowing to the engine because the fuel line will follow gravity inside your tank. Without one, you increase the chance that your plane may stall when flying inverted or performing different maneuvers. Installing a fuel clunk is simple to install and an investment that any serious pilot should make.

13x16mm

.4 oz

Rcexl-Glow-igniter-2214

$21.99 21.99

Miracle 19mm V4 Standard Heavy Duty Servo Arm-Half (Futaba/Hitec/JR)

MRC-F-028-Servo-Half-Arm

$10.99 10.99

Lemon RX DSMP (DSMX/DSM2 COMPATIBLE) MICROBRICK WITH 2 ON-BOARD SERVOS and MOLEX 2.00MM CONNECTOR PACKAGE

Lemon RX DSMP (DSMX/DSM2 COMPATIBLE) MICROBRICK WITH 2 ON-BOARD SERVOS and MOLEX 1.25MM CONNECTOR PACKAGE

Description:

Lemon Rx DSMX Compatible 6-Channel Receiver + Lemon DSMX Compatible Satellite

Type:	DSMX Compatible Full Range Receiver
Number of Channel:	6
Modulation:	DSMX Compatible (Also DSM2 backward Compatible)
Band:	2.4 GHz
Dimension:	25(L) x 18(W) x 11(H) mm
Weight:	4.5 grams + 2.5 grams
Voltage Range:	3.45 - 8.4 V

Highlight
- FailSafe for all channels via press of a button
- DSMX Satellite port

Understanding the receiver

Setup Instruction

Binding

Plug bind plug to the receiver.
Provide power to the unit. LED flashes quickly.
Enable bind mode in transmitter and ensure distance separation of 2 meters from receiver. Solid LED light means binding is completed.
Remove bind plug.

Setting Failsafe

Start by binding the receiver to the transmitter in the normal way and proceed as follows to set failsafe
Ensure that transmitter and receiver are turned on.
Insert bind plug into the receiver (Note: to set failsafe, bind plug is applied only when the receiver is turned on).
Set transmitter controls to the desired failsafe positions.
Press the side pushbutton to memorize failsafe settings.
Observe that the green light at the end of the receiver turns on to indicate failsafe is set. (Repeat step 4 will cause the LED to turn off which means failsafe is disabled).
Remove bind plug.
Disconnect the power for at least 2 seconds and then reconnect the power again. Test failsafe by turning off the transmitter.