Switches and Wires

Switches and Wires


Products

Male to Male Servo Extension Converting Wire

Male to Male Servo Extension Converting Wire

Description:

3” male to male servo extension. This wire allows you to easily and quickly convert an item ending in a female plug to a male. This often has applications in our hobby, allowing you to essentially change the plug at the end of your battery or other electronics from a female to a male without having to cut and re-solder


EX-MM3

$3.99

Micro Deans Connectors

Micro Deans Connectors

Description:
5 Pairs of Deans Style Connectors

Nylon T-connectors. These are VERY similar to Dean's style T connectors, and are fully compatible with Deans connectors.
Pack includes 5 male and 5 female connectors.



These connectors are made from Nylon, making them very tough and difficult to melt, even with the worst of soldering skills.
 





Features:

  • Durable nylon connectors
  • Compatible with Deans large connectors
  • Easy to solder
  • Positive/negative can only connect one way ensuring proper polarity



PRICE FOR PACKS OF 5 PAIR:

EX-Micro

$4.95

Miracle Replacement Switch

Miracle Replacement Switch

Replacement Switch and wire for Miracle switches.

With this switch and wire, you can easily replace a switch in a Miracle RC product. Perfect for if you have a crash and you want to be sure the switch is in perfect working condition. Or if you accidently damage your Miracle switch while working with it.

Just simply unscrew your old Miracle switch, loosen the grub screw that holds the plastic plug, and place the new one in. In about 5 minutes you'll have a brand new conditioned Miracle switch

MS-R

$4.99

MPI Charge Switch with On-board Battery Checker

MPI Charge Switch with On-board Battery Checker

Untitled Document

Description:

MPI Charge switch with LED indicator for HiTec and JR leads and on-board battery checker! The three LEDs - green, yellow, & red - monitor the status of the flight pack. It is designed to test the battery under the actual load of the on-board equipment.

The switch is factory preset to 4.8V applications - but for 6V use, simply cut the jumper loop on the back of the switch and seal the wires with silicone glue or tape. The jumper wires can be reconnected for 4.8V operation.

Features:

  • Heavy duty switch and wires
  • Sturdy one-piece design
  • Built-in Redundancy
  • 3-LED on-board battery checker
  • Compatible with 4.8v and 6v Rx packs
  • Easy installation and operation
  • Silicone shock mount included
  • DSC compatible
 

MPI-5470

$25.00

Optical Kill Switch

Optical Kill Switch

Description:
The Optical Kill Switch for gas rc planes, allows you to safely and remotely kill your electronic ignition. It is Fiber Optically Coupled to isolate your ignition system from your radio system so there is NO interference



Features:
  • Includes a remote mountable bright LED to indicate when the ignition is armed.
  • Fiber Optic coupled input/output.
  • Li-Po/Li-lon/A123/Ni-Mh/NiCad Input.
  • Up to 20 Volt 16 amp MOS-FET(IRF7456) output.
  • Low to 3Volt 3amp output.
  • Low Voltage Drop-Less than 150mv.
  • 100% Surface Mount Technology.
  • Heavy Gauge Wires,universal connectors.
  • Small and light weight –only 0.3 OZ!(8g)
  • Reverse Bettery input protection.
  • Shut down the transmitter power or receiver to cut off automatically when kill engine


Opto

$19.99

RC Exl Servo Y

RC Exl Servo Y

Description:
Our 6” heavy-duty Y-harnesses are perfect for standard servos up to 1/4 scale servos. They offer 22awg wire, gold plated connectors and thick wire jackets. Y-junction located in the middle of the harness and is a solid plastic housing rather than the cheaper heat shrink Ys.

Perfect for getting 2 leads out of one RX port.

1 servo Y per unit:

EX-Y

$2.99

RCexl Mini Tachometer

RCexl Mini Tachometer

Description:
You can use this RCexl mini tachometer to hook up directly to the ignition on the JC 28cc, or DLE engines to be able to view your RPM's at a glance. You can mount this mini-tach in your cockpit, or other visible area, and it runs off the battery power already supplied to your ignition. This is the newest RCexl (RCxl RCexcel) Version



Specifications:
  • Input Voltage between 3.5 and 8.4 volts
  • Current Consumption 25-60mA
  • Size: 41mmx17mmx12mm
  • Weight: .3oz



Features:
  • Indicates up to 30,000 RPM
  • Has and ULTRA-Bright LED so it can be easily read in daylight
  • Standard Futaba plug
  • Includes a Y Harness


Mini-Tach

$15.99

Redwing LED Power Board Display

Redwing LED Power Board Display

LED display light with male JR connector for RedwingRC Power Boards.

PB-LED

$4.99