Switches and Wires

Switches and Wires


New Arrivals

more...

Products

Booma IM14- Intellimatch Servo Matching System

NEW

Booma IM14- Intellimatch Servo Matching System

Description:

Welcome to the world’s first Automatic Intelligent Servo Matching System (ISMS)

Intellimatch is the result of 2 years of research and development, is designed to take the worry out of servo matching and gives you the maximum power, smoothest response and increased life from your servos.

If you have built giant scale models before with multi servo control surfaces then I am sure you will be familiar with the process of manually matching the servos. You generally match servos on 2 end points and maybe a center point. That’s a total of only 3 matching points. There is no way 3 points will accurately match your servos. Also, you have to adjust each servo until minimal buzz is heard or you might use an ammeter to minimize current draw. Throw that idea away...

With the Booma RC Intellimatch you say goodbye to traditional methods of servo matching. The Intellimatch system automatically matches servos on 100 points through the servo sweep range. That is 100 points not just the traditional 2 or 3. Intellimatch further adds smoother operation by reading the closest 2 points from the servos current position and then interpolates between the 2 selected points to a resolution of 8192 steps. 8192 step resolution is the highest resolution available today.

The IM14 Intellimatch unit is designed to match 1 set of up to 4 servos. An example IM14 usage might be up to 4 rudder or ailerons servos

Read on for the full list of features




Model Example 1 - 100cc Scale Aero Model:

-2 Aileron Servos per aileron

-1 Elevator Servo per elevator

-2 Rudder servos

Suggested Power Bus Intellimatch Accessories

-2 x IM22 = 1 x IM22 for Ailerons and 1 x IM22 for Elevators

Model Example 2 - 150cc Scale Aero Model:

-3 Aileron Servos per aileron

-2 Elevator Servo per elevator

-3 Rudder servos

Suggested Power Bus Intellimatch Accessories:

-1 x IM22 = 1 x IM22 for Elevators

-2 x IM14 = for Ailerons

-1 x IM14 = for Rudder

Model Example 3 - Large Jet:

-2 Aileron Servos per aileron

-2 Flap Servos

-1 Elevator Servo per elevator

-2 Rudder servos

Suggested Power Bus Intellimatch Accessories:

-1 x IM22 = for right side Ailerons and Flaps

-1 x IM22 = for left side Ailerons and Flaps

-1 x IM22 = for Rudder



Specs:

  • 32 bit Processor for the highest speed and resolution in the industry
  • Automatic matching of up to 4 servos on a single channel
  • 100 matched point across the servo sweep range
  • 82 step real time interpolation between the 100 matched points
  • PWM resolution of up to 8200 steps
  • Dual LED indication for programming feedback
  • Recommended battery chemistry - Life (2 cells), LiPo (2 cells), Lion (2 cells), NiCd(5cells),Nimh(5 cells)
  • Maximum input voltage 10 volts
  • Minimum input voltage 5 volts
  • Compatible with all receivers and Power Distribution systems
  • Works with Advanced Radio AR1232 and AR824. Also compatible with all other receiver and Power Distribution systems
  • Dual fail safe arming with the supplied arming plug
  • On board Flash storage - 100 year data retention
  • Weight is only 12 grams
  • Dimensions 49mm x 23mm (3.5 x 2.5 inches)

BRC-IM-14

$99.99

Charging Wire – Deans to Banana Plug

Charging Wire – Deans to Banana Plug

Description:

Short 3 wire to keep tangled wires to a minimum when charging batteries outside of your plane. You can still charge the batteries inside your plane as long as you can get the charger relatively close to the wire or port. Ideal for a multi charger since you won’t have 4 or more super long wires getting tangled and twisted as you try to charge your batteries.

 

EX-CH-DB-3

$3.99

Deluxe Power Board LED light

Deluxe Power Board LED light

Deluxe Power Board LED light
Super Bright!

BB-PB-light

$2.99

Mini Switch

Mini Switch

Mini Switch

BB-Mini-Switch

$3.99

$2.49

RCEXL High Current Electronic Switch

RCEXL High Current Electronic Switch

Description:

Booma RC

Booma RC pin flag switch for IntelliReg, Smart-Fly or Gryphon regulator. This pin flag switch Booma RC is an ultra high quality fail safe switch designed as a replacement switch for Smart-Fly systems, Power System, Power Expander, Regulators as well as Gryphon Heli regulators.

Supplied with 1 x switch actuator and 1 x pin flags.



rcexl-hv-switch

$39.95

$35.95

Tech Aero IBEC

Tech Aero IBEC

Tech Aero BEC

TA-BEC

$44.95

$39.95

XPERT ELECTRONIC SWITCH

XPERT ELECTRONIC SWITCH

Mini Switch

Xpert-Switch

$21.99

$18.99

Power Board - PRO SERIES - Red (4104)

Power Board - PRO SERIES - Red (4104)

 

 

 

 

All NEW 4000 SERIES! *with Digital Readout and Touch-button programming.

Description:

Completely redesigned from the ground up, with these new Power Boards you are able to use 2 batteries with redundancy to avoid possible crashes from battery failure. Simply plug in your batteries with XT-60 style connectors to this Power Board Expander (Our LiFe batteries are perfect for this) and you now have 2 batteries working in tandem to supply your servos AND ignition.


These new versions offer SEVERAL new features:
1) Digital read out on all models - displaying voltage going IN and OUT of all devices (see photo)
2) LED and audible alarm for all models that you can set to warn when your system drops below a voltage of your choosing
3) TOUCH button programming to select your warning voltage
4) Wires to your RX are PRE-installed
5) Enclosed lightweight and strong plastic housing
6) XT-60 Connectors

The Power Board board electronically isolates the batteries from each other so that there is no interference possible from your ignition. It also regulates the voltage down to an ideal voltage to your RX (5v) and then is select-able to your servos (yellow and black units only - the red unit offers the same voltage as your batteries to the servos).

You can Plug in, up to 8 servos into the board (12 servos with the Black Power Board), which has 2 outputs for EACH channel, effectively DOUBLING the number of servos you can use in a plane ( a total of 16 output channels) without reducing the amperage (that a Y cable would cause).

These Power Boards also features LED lights to give you clear indication that your batteries are connected and working properly, as well as voltage etc.

They feature a mounting space in the middle to mount your RX and also include mounting hardware to mount it securely to your plane.





Watch this video for an overview of the different versions


View this video for a full explanation on how to use these power boards




Features:

Red Power Board (4104)

  • Dual battery redundancy for safer flying
  • LCD display which shows real time info of your in and out voltages
  • Built in regulator that supplies a clean 5v to your receiver
  • Integrated CDI remote cut off switch to kill your engine (OPTO KILL)
  • 8 channels in, 16 channels out (+ ignition)
  • Electronically isolated for interference free flying

    (We recommend our LiFe batteries and 6v servos with this unit - be sure to select ones with XT connectors for this use)



Specs:

Red Power Board (4104)

  • Input Voltage: 5-13v
  • Working load: 0A to 20A
  • Weight: 3 oz.
  • Dimensions: 4.5"x2.5"x5/8"
  • Working Temperature: -20c to -85c




Recommended Set ups: Use the Red Power Board for 30-50cc planes using 6v servos. Use 2 LiFe batteries, and "jump" power down from an open servo port on the board, to run to your ignition

PB-4104

$99

Power Board - PRO SERIES - Black (4106)

Power Board - PRO SERIES - Black (4106)

 

 

 

 

 

 

 

 

All NEW 4000 SERIES! *with Digital Readout and Touch-button programming.

Description:

Completely redesigned from the ground up, with these new Power Boards you are able to use 2 batteries with redundancy to avoid possible crashes from battery failure. Simply plug in your batteries with XT-60 style connectors to this Power Board Expander (Our LiFe batteries are perfect for this) and you now have 2 batteries working in tandem to supply your servos AND ignition.


These new versions offer SEVERAL new features:
1) Digital read out on all models - displaying voltage going IN and OUT of all devices (see photo)
2) LED and audible alarm for all models that you can set to warn when your system drops below a voltage of your choosing
3) TOUCH button programming to select your warning voltage
4) Wires to your RX are PRE-installed
5) Enclosed lightweight and strong plastic housing
6) XT-60 Connectors

The Power Board board electronically isolates the batteries from each other so that there is no interference possible from your ignition. It also regulates the voltage down to an ideal voltage to your RX (5v) and then is select-able to your servos (yellow and black units only - the red unit offers the same voltage as your batteries to the servos).

You can Plug in, up to 8 servos into the board (12 servos with the Black Power Board), which has 2 outputs for EACH channel, effectively DOUBLING the number of servos you can use in a plane ( a total of 16 output channels) without reducing the amperage (that a Y cable would cause).

These Power Boards also features LED lights to give you clear indication that your batteries are connected and working properly, as well as voltage etc.

They feature a mounting space in the middle to mount your RX and also include mounting hardware to mount it securely to your plane.





Watch this video for an overview of the different versions


View this video for a full explanation on how to use these power boards




Features:


Black Power Board (4106)

  • Dual battery redundancy for safer flying
  • LCD display which shows real time info of your in and out voltages
  • Built in regulator that supplies a clean 5v to your receiver
  • Integrated CDI remote cut off switch to kill your engine (OPTO KILL)
  • 8 channels in, 16 channels out (+ ignition)
  • Electronically isolated for interference free flying
  • Adjustable voltage selection to your servos via the dial on the side (from 4.8v to 9.7)
  • Ability to use High voltage servos while providing a clean 5v to your RX
  • Battery balancing (draws extremely evenly from your dual battery set up)
  • Short Circuit protection (in the unlikely event of a short it will protect from battery drain)

    (input voltage MUST be between 6-13v. A 4S Life would be ideal)



Specs:

Black Power Board (4106)

  • Input Voltage: 6-13v
  • Working load: 0A to 30A
  • Weight: 4.5 oz.
  • Dimensions: 4.5"x2.5"x5/8"
  • Working Temperature: -20c to -85c



Recommended Set ups: Use the Black Power Board for 50cc to 100cc or bigger.

PB-4106

$135

Power Board - PRO SERIES - Yellow (4105)

Power Board - PRO SERIES - Yellow (4105)

 

 

 

 

 

 

 

 

 

 

 

 

All NEW 4000 SERIES! *with Digital Readout and Touch-button programming.

Description:

Completely redesigned from the ground up, with these new Power Boards you are able to use 2 batteries with redundancy to avoid possible crashes from battery failure. Simply plug in your batteries with XT-60 style connectors to this Power Board Expander (Our LiFe batteries are perfect for this) and you now have 2 batteries working in tandem to supply your servos AND ignition.


These new versions offer SEVERAL new features:
1) Digital read out on all models - displaying voltage going IN and OUT of all devices (see photo)
2) LED and audible alarm for all models that you can set to warn when your system drops below a voltage of your choosing
3) TOUCH button programming to select your warning voltage
4) Wires to your RX are PRE-installed
5) Enclosed lightweight and strong plastic housing
6) XT-60 Connectors

The Power Board board electronically isolates the batteries from each other so that there is no interference possible from your ignition. It also regulates the voltage down to an ideal voltage to your RX (5v) and then is select-able to your servos (yellow and black units only - the red unit offers the same voltage as your batteries to the servos).

You can Plug in, up to 8 servos into the board (12 servos with the Black Power Board), which has 2 outputs for EACH channel, effectively DOUBLING the number of servos you can use in a plane ( a total of 16 output channels) without reducing the amperage (that a Y cable would cause).

These Power Boards also features LED lights to give you clear indication that your batteries are connected and working properly, as well as voltage etc.

They feature a mounting space in the middle to mount your RX and also include mounting hardware to mount it securely to your plane.





Watch this video for an overview of the different versions


View this video for a full explanation on how to use these power boards




Features:

Yellow Power Board (4105)

  • Dual battery redundancy for safer flying
  • LCD display which shows real time info of your in and out voltages
  • Built in regulator that supplies a clean 5v to your receiver
  • Integrated CDI remote cut off switch to kill your engine (OPTO KILL)
  • 8 channels in, 16 channels out (+ ignition)
  • Electronically isolated for interference free flying
  • Adjustable voltage selection to your servos via the dial on the side (from 4.8v to 9.7)
  • Ability to use High voltage servos while providing a clean 5v to your RX

    (Please note the input voltage for this unit MUST be between 7v-13v. A 4S LiFe would be ideal)
     



Specs:

Yellow Power Board (4105)

  • Input Voltage: 7-13v
  • Working load: 0A to 30A
  • Weight: 3.5oz.
  • Dimensions: 4.5"x2.5"x5/8"
  • Working Temperature: -20c to -85c



Recommended Set ups: Yellow board for 30cc to 100cc or larger using ANY servos.

PB-4105

$119

Servo Extensions

Servo Extensions

Description:
High quality 22AWG wire, twisted silicone wire extensions. JR type connections, so they will plug into any receiver/switch, and most servos (Hitec/JR/PowerHD/etc etc....futaba you would have to trim the edge off).
 

  • Soft flexible silicone casing
  • Heavy duty 22awg
  • Universal - XQ Power/Hitec/Power HD/JR/more...
  • Reliable! We've NEVER gotten a pair returned

    Prices
    • 2" 1 pair - $2.50
    • 2" 2 pair - $4.50
    • 2" 3 pair - $6.99
       
    • 3" 1 pair - $3.50
    • 3" 2 pair - $6.50
    • 3" 3 pair - $8.99
       
    • 6" 1 pair - $3.99
    • 6" 2 pair - $6.99
    • 6" 3 pair - $9.99
       
    • 8" 1 pair - $3.99
    • 8" 2 pair - $6.99
    • 8" 3 pair - $9.99
       
    • 10" 1 pair - $3.99
    • 10" 2 pair - $6.99
    • 10" 3 pair - $9.99
       
    • 12" 1 pair - $4.99
    • 12" 2 pair - $8.99
    • 12" 3 pair - $12.99
       
    • 14" 1 pair - $4.99
    • 14" 2 pair - $8.99
    • 14" 3 pair - $12.99
       
    • 16" 1 pair - $4.99
    • 16" 2 pair - $8.99
    • 16" 3 pair - $12.99
       
    • 18" 1 pair - $6.99
    • 18" 2 pair - $10.99
    • 18" 3 pair - $13.99

    • 24" 1 pair - $7.99
    • 24" 2 pair - $12.99
    • 24" 3 pair - $15.99
       
    • 28" 1 pair - $7.99
    • 28" 2 pair - $12.99
    • 28" 3 pair - $15.99
       
    • 32" 1 pair - $7.99
    • 32" 2 pair - $12.99
    • 32" 3 pair - $15.99
       
    • 36" 1 pair - $8.99
    • 36" 2 pair - $14.99
    • 36" 3 pair - $17.99

    • 44" 1 pair - $8.99
    • 44" 2 pair - $14.99
    • 44" 3 pair - $17.99
       
    • 48" 1 pair - $8.99
    • 48" 2 pair - $14.99
    • 48" 3 pair - $17.99
       

EX-02

$2.50

Servo Safety Clips

Servo Safety Clips

Description:
10 pack of servo safety clips. Made to retain your servo wires to keep them from slipping off during flight.

A must have to to ensure your servo connectors stay securely connected.

Packs of 10:

EX-clip

$5.95

$4.95