APC 20 x 11 Electric Prop

MKS HBL850

Description:

The MKS HBL850 is a high quality Digital "Brushless" Servo with all aluminum casing and metal gears. The heat sink on the outside of this servo is very helpful for dissipating the heat and keeping your system cool.

NOTE: This high torque servo uses a large 8mm output shaft. Traditional servo arms will not fit.

New and Improved Technology!

Why choose brushless servos? They have many benefits, one being that they only use the power necessary to get the job done. If the servo encounters resistance then more power is given, if it senses less resistance then less power is given. With brush servos, full power is used no matter what the situation.

Specs:

• Torque:
  • 252.75 oz/in at 6V (18.2 kg/cm)
  • 312.47 oz/in at 7.4V (22.5 kg/cm)
  • 345.80 oz/in at 8.4V (24.9 kg/cm)
     
• Speed:
  • .1 sec at 6V
  • .079 sec at 7.4V
  • .071 sec at 8.4V
     
• Voltage: 4.8V to 8.4V
• Weight: 2.57 oz (73g)
• Size:1.39 x .59 x 1.12 in (35.5 x 15.0 x 28.5 mm)
   
• Operating Temp- -10~60centigrade
• Working Frequency - 1520μs / 333hz
• Dead Band- 0.0008ms
• 29.5 cm connector wire
• BRUSHLESS Motor
• Indirect Potentiometer Drive
• Double ball bearings
• All Aluminum casing
• Chrome-Titanium alloy gears

Description:

The Power-HD DSM44 digital servo is a micro servo with digital control electronics for increased performance. Just like the Power-HD DSP33 ,the DSM44 is also very light and ranks as the secont lightest servo at RedwingRC- weighing only slightly over 6g!!! In the DSM44, the output shaft is supported by a ball bearing for decreased friction, and another great feature is that most of the gears are metal for increased durability! The lead is terminated with a Futaba-compatible standard “JR”-style connector. Servo horns and associated hardware are included.

It is important to note that stalling or back-driving this servo can strip its gears.



Specifications:

• Torque:
  16.66 oz/in at 4.8V (1.2 kg/cm)
  22.21 oz/in at 6V (1.6 kg/cm)
   
• Speed:
  .09 sec at 4.8V
  .07 sec at 6V
   
• Voltage: 4.8v to 6v
• Weight: .24oz (6.75 g)
• Size: .68 x .87 x 1.06in (22 x 8.7 x 27mm
   
• Digital
• Lead Length: 160 mm
• Storage Temperature: -20℃~60℃
• Operating Temperature: -10℃~50℃
• Hardware included
• Suitable for F3P/EPP/KT Airplanes

Lemon RX DSMP (DSMX/DSM2 COMPATIBLE) MICROBRICK WITH 2 ON-BOARD SERVOS and MOLEX 1.25MM CONNECTOR PACKAGE 

Description:

Lemon Rx DSMX Compatible 6-Channel Receiver + Lemon DSMX Compatible Satellite

Highlight
- FailSafe for all channels via press of a button
- DSMX Satellite port

Understanding the receiver

Setup Instruction

Binding

1. Plug bind plug to the receiver.
2. Provide power to the unit. LED flashes quickly.
3. Enable bind mode in transmitter and ensure distance separation of 2 meters from receiver. Solid LED light means binding is completed.
4. Remove bind plug.

Setting Failsafe

1. Start by binding the receiver to the transmitter in the normal way and proceed as follows to set failsafe
2. Ensure that transmitter and receiver are turned on.
3. Insert bind plug into the receiver (Note: to set failsafe, bind plug is applied only when the receiver is turned on).
4. Set transmitter controls to the desired failsafe positions.
5. Press the side pushbutton to memorize failsafe settings.
6. Observe that the green light at the end of the receiver turns on to indicate failsafe is set. (Repeat step 4 will cause the LED to turn off which means failsafe is disabled).
7. Remove bind plug.
8. Disconnect the power for at least 2 seconds and then reconnect the power again. Test failsafe by turning off the transmitter.