Bob Smith Industries Maxi-Cure Exra Thick CA

Contact UsCustomer Reviews

Bob Smith Industries Maxi-Cure Exra Thick CA

Our Price:

$4.99


Size
Quantity (13)

Availability 13 in stock
Weight 0.31 lbs
SKU BSI-CA-135
Manufacturer BSI Bob Smith Industries

Untitled Document

Description:

Bob Smith Industries CA Glue

Maxi-Cure™ Super Glue, CA

Maxi-Cure™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE™ bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, clothtextured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE™ or any other adhesive. It also is best for bonding the tires for R/C cars.

Directions:

Unscrew top from nozzle. For finer applications, use the extender tip. Apply Maxi-Cure™ CA to one side of the parts being joined, then hold them tightly to- gether for 10-20 seconds. For larger bonding areas, apply serpentine beads of the CA with enough spacing to allow for the spreading of the adhesive. Insta-Set™ accelerator can be sprayed to cure the CA that oozes from joints. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220° F. Soak extender tip in acetone for cleaning.

 

Works Best On:

  • Soft Wood
  • Hard Wood
  • Glass & Metal
  • Fiberglass
  • Ceramics
  • Hard Plastics
  • Rubber
  • Laminating
  • Reinforcing

Works Good On:

  • Balsa Wood
  • Water-Resistant

 

Click to Download Safety Data Sheet

: *
: *
: *
 

Bob Smith Industries Insta-Cure Super Thin CA

Untitled Document

Description:

Bob Smith Industries CA Glue

Insta-Cure™

Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond.

Works Best On:

  • Balsa Wood
  • Ceramics

Works Good On:

  • Soft Wood
  • Fiberglass
  • Hard Plastics
  • Water-Resistant
  • CA Hinges

 

Avaliable in 2oz and 3/4 Pocket Size.

Pocket CAs feature a new top that has a pin built into the cap that covers the nozzle. This pin seals the bottle so that if it is tipped over, the bottle will not leak. This makes the Pocket CAs ideal for keeping in your tool or field box, just like our IC-Gel. One disadvantage that the new Pocket CA top has is the bluntness of the nozzle. This makes it more difficult to apply small amounts of the CA, especially in tight places. From the feedback we have received, it appears about 25-30% of users prefer the new Pocket CA top, which means that over 70% prefer our standard top for general bonding purposes. Most users are buying both types. Our original top for the workshop, and the Pocket CA for use out in the field. The 3/4 oz. Pocket CAs are available in BSI's Insta-Cure, Insta-Cure+, Maxi-Cure and Super-Gold+. BSI's new extender tip #304 works on the Pocket CA.

 

Click to Download Safety Data Sheet

 

 

 

BSI-CA-

$4.99

Bob Smith Industries Insta-Cure+ Gap Filling CA

Untitled Document

Description:

Bob Smith Industries CA Glue

Insta-Cure+™ Super Glue, CA

Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out.

Directions:

Unscrew top from nozzle. For finer applications, use the extender tip. Apply Insta-Cure+™ CA to one side of the parts being joined, then hold them tightly together for 5-15 seconds. For larger bonding areas, apply serpentine beads of the CA with enough spacing to allow for the spreading of the adhesive. Insta-Set™ accelerator can be sprayed to cure the CA that oozes from joints. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220° F. Soak extender tip in acetone for cleaning

 

Works Best On:

  • Balsa Wood
  • Soft Wood

Works Good On:

  • Hard Wood
  • Glass & Metals
  • Fiberglass
  • Ceramics
  • Hard Plastics
  • Rubber
  • Laminating
  • Water-Resistant
  • Reinforcing

 

Avaliable in 2oz and 3/4 Pocket Size.

Pocket CAs feature a new top that has a pin built into the cap that covers the nozzle. This pin seals the bottle so that if it is tipped over, the bottle will not leak. This makes the Pocket CAs ideal for keeping in your tool or field box, just like our IC-Gel. One disadvantage that the new Pocket CA top has is the bluntness of the nozzle. This makes it more difficult to apply small amounts of the CA, especially in tight places. From the feedback we have received, it appears about 25-30% of users prefer the new Pocket CA top, which means that over 70% prefer our standard top for general bonding purposes. Most users are buying both types. Our original top for the workshop, and the Pocket CA for use out in the field. The 3/4 oz. Pocket CAs are available in BSI's Insta-Cure, Insta-Cure+, Maxi-Cure and Super-Gold+. BSI's new extender tip #304 works on the Pocket CA.

 

Click to Download Safety Data Sheet

 

 

 

 

BSI-CA-56b908caadc59

$4.99

CDI Remote Kill Switch

Description:
The Optical Kill Switch for gas rc planes, allows you to safely and remotely kill your electronic ignition. It is Fiber Optically Coupled to isolate your ignition system from your radio system so there is NO interference



Features:

  • Includes a remote mountable bright LED to indicate when the ignition is armed.
  • Fiber Optic coupled input/output.
  • Li-Po/Li-lon/A123/Ni-Mh/NiCad Input.
  • Up to 20 Volt 16 amp MOS-FET(IRF7456) output.
  • Low to 3Volt 3amp output.
  • Low Voltage Drop-Less than 150mv.
  • 100% Surface Mount Technology.
  • Heavy Gauge Wires,universal connectors.
  • Small and light weight –only 0.3 OZ!(8g)
  • Reverse Bettery input protection.
  • Shut down the transmitter power or receiver to cut off automatically when kill engine






  •  
  •  
  •  
  •  

RCCSKJ-SW-CDI-Kill-4112

$17.99