5-Function Mini/Micro Charge Adapter to Male 4mm Bullets

5-Function Mini/Micro Charge Adapter to Male 4mm Bullets

Market Price: $12.99
Our Price:

$9.99

You Save

23%

Quantity (25)

Availability 25 in stock
Weight 0.40 lbs
SKU EX-HRP-RCE1625

Description:

5-Function Mini/Micro Charge Adapter to Male 4mm Bullets-300mm 

Racer's Edge provides a convenient charging solution for mini and micro air or surface models. Includes five of the most popular connectors in this category: Mini-Molex (Tamiya), JR-type receiver, JST, Hubsan-type, and Micro BLH/EFL. 


: *
: *
: *
 
 

Bob Smith Industries Foam-Cure

Untitled Document

Description:

Bob Smith Industries Foam Cure

Foam-Cure™

FOAM-CURE™ is a silicone based adhesive that works very well on EPP and EPO foams. It is crystal clear and cures to a more flexible consistency than CA. It is, however, not instant bonding like CA and there is no accelerator to speed it’s curing. To obtain a faster initial bond when bonding two pieces, FOAM-CURE™ can be applied to one piece and after the two are joined, they can then be pulled apart. After letting it air dry for about ten minutes, FOAM-CURE™ will act like a contact cement when the parts are rejoined, resulting in enough tack strength to allow the next steps of assembly. Full strength is reached in 10-12 hours.

FOAM-CURE™ works with all foams, and will actually bond most other materials. It will bond wood and plastic to foam, and is a good canopy glue. FOAM-CURE™ does not, however, cure flexible enough to act as a hinge for aircraft control surfaces. Its limitations occur when bonding large areas of two non-porous materials. FOAM-CURE™ requires exposure to air for drying. If one tried to bond, for example, a half-dollar coin to glass, over 90% of the adhesive would never cure, since the solvent it contains would have no where to evaporate. A small amount of denatured alcohol can be mixed into the Foam-Cure to make it thinner.

 

Works Best On:

  • EPP Foam
  • EOP Foam
  • Clear Canopy
  • Paper and Crafts

 

Cut off tip of nozzle. Apply to one part before joining. Use tape to hold parts in place during cure. For faster curing, pull the joint apart and let Foam-Cure™ air dry for 5-10 min before rejoining the parts. This results in enough tack strength to allow the next steps of assembly. Full cure takes 10-12 hours. Foam-Cure™ works on all foams, especially on EPP and EPO, and will bond a porous surface to non-porous materials. Foam-Cure™ is also an excellent glue for clear canopies, and will also bond paper. If needed, denatured alcohol can be used to thin or clean up uncured Foam-Cure™. Replace cap after use.

 

Click to Download Safety Data Sheet

 

BSI-AC

$2.99

Redwing 3S Lipo Batteries

Description:

Redwing 2S 2200 mah Lipo Batteries.

These batteries are lightweight with a high density of energy and low internal resistance. Lipo batteries have a long life and will provide the power you need when you need it.

These batteries have the XT60 connector, JR connector, and Balance plug



Specifications:

  • Type: Lipo Battery
  • Weight:
    • 2200mah - 5.2 oz.
  • Size:
    • 2200mah- 10.5cm x 3.5cm x 1.5cm
  • Voltage: 7.4Volts
  • 2 cells (2s)
  • Connectors: XT-60 Connector
  • Also a balancing lead
  • 2200mah - $14.99

LiPo-3S-

$24.99

FUTABA 18MZ A 2.4GHz FASST Aircraft Spec Radio System w/2x R7008SB Receivers

 

 

 

 

 

 

 

 

 

 

 

 

Product Description

With 4 times the resolution of its predecessor, the Aurora 9, the Aurora 9X is sure to become a favorite among the most demanding pilots. It is HiTec's first triple protocol radio which allows selection from the G1 and G2 Adaptive Frequency Hopping Spread Spectrum (AFHSS) or Secure Link (SLT) 2.4GHz technologies. It features dual processors for fast low latency response and ultra-smooth 4096 resolution. With more than 30 additional programming enhancements and new dynamically assignable switches, it is sure to thrill sport and professional level airplane and helicopter pilots alike.


Features

  • Built in AFHSS 2.4GHZ / SLTTM Module (Single / Bi-Directional Selectable)
  • 4096 Resolution
  • Improved Latency (Dual Processor 7ms Frame Rate)
  • Vibration Mode
  • Included Touch Screen Stylus
  • Easy-to-Read, Easily Accessible 5.1-inch Wide Backlit LCD Touch Screen (320 x 80 Pixels)
  • Customizable Menu
  • One-Stop Model Type Setting
  • 3 Multi-Tasking Digital Trims
  • Fully Assignable Control Switches, Knobs, Sticks and Digital Trims
  • Ultra-Smooth Quad Ball Bearing Gimbals
  • Full-Size Comfortable Hand Grips (Top Quality Elastomer)
  • Selectable 4 Different Control Stick Modes, Plus 2 Additional Manual Modes (Software)
  • Easy Gimbal Mode Change and Tension Adjustment (Hardware)
  • Power Management System (Adjustable Backlight & Auto Shut-off Time)
  • Digital Trim Nano-Adjuster (200 Adjustable Trim Steps)

Standard Programming

  • 9 Assignable Control Channels
  • 3-Model Type Programming (ACRO/GLID/HELI)
  • 30-Model Memory
  • 20 Character Model Naming
  • 8 Flight Conditions with 10 Characters
  • Fail-Safe
  • Channel Function
  • EPA
  • Dual Rate & EXP* 
  • Sub-Trim
  • Servo Reverse
  • Servo Speed (up to 25 sec. in each direction)* 
  • Servo Monitor (Monitor & Servo Test)
  • 8 Programmable Mixes (5x 2-Point, 3x 7-Point Curves)**
  • Trainer
  • Throttle Lock

* Capable of a Maximum of 24 rates by 8 flight conditions and 3 switch positions
** Capable of a Maximum of 8 Rates by 8 Flight Conditions

HRP-FUT01004377-1

$3099.99