Bob Smith Industries Mid-Cure Epoxy
Bob Smith Industries Epoxy
MID-CURE™ 15 min. epoxy is used in larger areas where more working time is needed. It is more water resistant and can be used as a substitute for QUIK-CURE™ in most applications. MID-CURE™ is our most flexible epoxy and is ideal for gluing to fiberglass surfaces. Allow 45 minutes before handling parts and 2 hours for full strength.
Works Best On:
Works Good On:
Avaliable in 4.5oz Size.
MID-CURE™ 15 min. Epoxy is an equal two-part hobby adhesive that forms high strength bonds through a chemical reaction between the resin and hardener. The cured epoxy is resistant to most chemicals.
MID-CURE™ should be applied in temperatures above 65˚F. It can be used in most applications when you need more working time than QUIK-CURE™ provides. MID-CURE™ can be worked for about 10 minutes, with adhesion beginning after about 15 minutes.
MID-CURE™ bonds best to clean, textured surfaces. Smooth, non-porous surfaces should be roughened with coarse sandpaper to improve adhesion. Acetone and Isopropyl rubbing alcohol work as the best solvents for cleaning uncured epoxy from surfaces. MID-CURE™ is our most flexible epoxy. This gives it superior bonding qualities in applications such as hardwood to fiberglass. MID-CURE’S™ lack of brittleness allows it to form lasting bonds in areas subject to high vibration or stress. MID-CURE™ is a water-resistant substitute for QUIK-CURE™. Full cure in 2-3 hours.
20cc EDGE 540 Profile - Yellow w/ Star Burst
New Design: 20cc Edge Profile
SIDE FORCE GENERATORS INCLUDED!
We DO ship our planes internationally!
Please contact us with your location for more specific cost.
Spot On 1.5" Servo Arm
High Quality 1.5" Aluminum servo arm from Spot-On RC
Spot On Servo Arms are made of high quality 7075-T6 aluminum, one of the highest strength alloys available for this purpose. They feature an ultra secure double lock design, keeping your servo arm secure and eliminating any slop between the main servo gear and the arm. Spot On Servo Arms are also sand blasted and anodized for a beautiful appearance.Spot on offers their servo arms in many sizes, threads and gear output compatibility. Spot On arms are offered in:
M3, or #4-40 holes, so you can use ball links that are metric or standard Futaba, Hitec or JR compatible gear mesh. Sizes ranging from 1” to 2” for single arms and 2.5” to 4.5” for rudder arms.
Available colors are Black or Silver
Spot On RC Servo Arms are measured from the center hole of the servo to the outermost hole (for example, a 1” arm is exactly 1” from hole center to hole center). However the larger sizes offer the option of one or two more additional inner holes so you can use them for future projects or fine tune your ratios.Redwing RC only offers the V2, upgraded version, with stronger aluminum and finer design. No matter which Spot On RC Servo Arms you choose you will be sure to experience problem free set up and operation with these high quality servo arms.
FUTABA 18MZA 2.4GHz FASST Aircraft Spec Radio System w/ R7008SB Receiver
With 4 times the resolution of its predecessor, the Aurora 9, the Aurora 9X is sure to become a favorite among the most demanding pilots. It is HiTec's first triple protocol radio which allows selection from the G1 and G2 Adaptive Frequency Hopping Spread Spectrum (AFHSS) or Secure Link (SLT) 2.4GHz technologies. It features dual processors for fast low latency response and ultra-smooth 4096 resolution. With more than 30 additional programming enhancements and new dynamically assignable switches, it is sure to thrill sport and professional level airplane and helicopter pilots alike.
* Capable of a Maximum of 24 rates by 8 flight conditions and 3 switch positions