EPP YAK55 3D Airplane 31.5" (800MM) Wingspan

EPP YAK55 3D Airplane 31.5" (800MM) Wingspan

Our Price:

$64.99

Optional Versions
Quantity (8)

Availability 8 in stock
Weight 2.25 lbs
SKU DW-E1704

31.5" EPP 3D Airplane YAK55
 

Features:
  • Kit version - Assemble and install your choice of electronics
  • All hardware accessories included in kit
  • Durable EPP material with realistic printing 
  • Simple to build

Specification:

  • Wingspan: 800mm 
  • Length: 875mm 
  • Flying Weight: 400g 

Suggested Power System: 

  • Motor: 2212 1400KV 
  • ESC: 20A 
  • Servo: 9g *4 
  • Propeller: SF 8-9inch
  • Radio: more than 4CH 
  • BATT: 2S 1200-1500mAh (Not incl.) 

Different versions supplied as below: 
E1701= YAK55 KIT+Prop (APC SF9047) 
E1702= YAK55 KIT+Motor(2212 1400KV+3.5mm Banana Male Plug+3.0mm Prop Adapter)
E1704= YAK55 KIT+Motor+ESC(20A E-Power+3.5mm Banana Female Plug+XT60 Plug)+Servo(9g*4)

: *
: *
: *
 
 

Fuel Filter


Description:
This is a handy break-apart fuel filter with screen for easy cleaning.

A very inexpensive way to ensure you don't suck dirt particles into your engine

SS-FFX

$3.99

Bob Smith Industries Foam-Cure

Untitled Document

Description:

Bob Smith Industries Foam Cure

Foam-Cure™

FOAM-CURE™ is a silicone based adhesive that works very well on EPP and EPO foams. It is crystal clear and cures to a more flexible consistency than CA. It is, however, not instant bonding like CA and there is no accelerator to speed it’s curing. To obtain a faster initial bond when bonding two pieces, FOAM-CURE™ can be applied to one piece and after the two are joined, they can then be pulled apart. After letting it air dry for about ten minutes, FOAM-CURE™ will act like a contact cement when the parts are rejoined, resulting in enough tack strength to allow the next steps of assembly. Full strength is reached in 10-12 hours.

FOAM-CURE™ works with all foams, and will actually bond most other materials. It will bond wood and plastic to foam, and is a good canopy glue. FOAM-CURE™ does not, however, cure flexible enough to act as a hinge for aircraft control surfaces. Its limitations occur when bonding large areas of two non-porous materials. FOAM-CURE™ requires exposure to air for drying. If one tried to bond, for example, a half-dollar coin to glass, over 90% of the adhesive would never cure, since the solvent it contains would have no where to evaporate. A small amount of denatured alcohol can be mixed into the Foam-Cure to make it thinner.

 

Works Best On:

  • EPP Foam
  • EOP Foam
  • Clear Canopy
  • Paper and Crafts

 

Cut off tip of nozzle. Apply to one part before joining. Use tape to hold parts in place during cure. For faster curing, pull the joint apart and let Foam-Cure™ air dry for 5-10 min before rejoining the parts. This results in enough tack strength to allow the next steps of assembly. Full cure takes 10-12 hours. Foam-Cure™ works on all foams, especially on EPP and EPO, and will bond a porous surface to non-porous materials. Foam-Cure™ is also an excellent glue for clear canopies, and will also bond paper. If needed, denatured alcohol can be used to thin or clean up uncured Foam-Cure™. Replace cap after use.

 

Click to Download Safety Data Sheet

 

BSI-AC

$2.99

EPP SBACH342 3D Airplane 39.4" (1000MM) Wingspan

31.5" EPP 3D Airplane YAK55 Features: • Kit version - Assemble and install your choice of electronics • All hardware accessories included in kit • Durable EPP material with realistic printing resemblance of a shark • Simple to build Specification: Wingspan: 800mm Length: 875mm Flying Weight: 400g Suggested Power System: Motor: 2212 1400KV ESC: 20A Servo: 9g *4 Propeller: SF 8-9inch Radio: more than 4CH BATT: 2S 1200-1500mAh (Not incl.) Different versions supplied as below: E1701=E17 YAK55 KIT+APC SF9047 E1702=E17 YAK55 KIT+Motor(2212 1400KV+3.5mm Banana Male Plug+3.0mm Prop Adapter) E1704=E17 YAK55 KIT+Motor+ESC(20A E-Power+3.5mm Banana Female Plug+XT60 Plug)+Servo(9g*4)

DW-E0904

$64.99