General Accessories

Heat shrink covering for RC planes

Please contact us for information on if your plane is using Ultracote, or TruCote before ordering if you are unsure

Description:
TruCote covering is a high tech polyester covering that is sensative to heat which makes it easy to apply to your plane. It offers high adhesion, fuel proof/waterproof covering for your plane. Easy to apply using a heat gun and/or iron.

• Specs:
• Width: 23.5”
• Temp to adhesion: Approximately 250 degrees F
• Shrinkage begins: Approximately 275 degrees F
• Maximum recommended temp: Approximately 300 degrees F

For instructions on how to apply covering here is a helpful tutorial:

http://www.rc-airplane-advisor.com/heat-shrink-covering.html


Sold in 1 Foot Sections. Please select how many feet you want.

Please put what plane this is for at checkout so that we can match it!

This package of 10 Pin Hinges are high quality steel pin hinges desinged to join your surfaces with strong free momvement. Built in the "Robart" style of hinge, they are strong and light and offer a high quality connection to your moving surfaces for 20cc or bigger planes

These hinges will install by drilling a 3/16" hole and inserting the hinge with a bit of glue.

---

Check out these Videos:

 

 

2-1 15A UBEC and Digital Switch

switch, 2-in-1-5A-UBEC-Digital-Voltage-Switch, RCCSKJ 2108#

2-in-1 Dual Power Switch w/digital display

Replacement Switch and wire for Miracle switches.

With this switch and wire, you can easily replace a switch in a Miracle RC product. Perfect for if you have a crash and you want to be sure the switch is in perfect working condition. Or if you accidently damage your Miracle switch while working with it.

Just simply unscrew your old Miracle switch, loosen the grub screw that holds the plastic plug, and place the new one in. In about 5 minutes you'll have a brand new conditioned Miracle switch
 

3-in-1 HV Switch with Digital Voltmeter and CDI Ignition switch, RCCSKJ, 2107#

3-in-1 Methanol Nitro Ignition with HV Switch with Digital Voltmeter, RCCSKJ, 2106#

4-Function Charge Adapter to Male 4mm Bullets (XT60, XT90, EC3, EC5)

8-Function Charge Adapter to Male 4mm Bullets-300mm Wire 

Racer's Edge provides an ideal solution for enthusiasts with multiple models using batteries with various connectors. This convenient charging squid comes equipped with virtually every possible connector that a modeler may require. Plugs included: Tamiya, Deans, TRX, XT60, JST, EC3, universal receiver pack, and if we've forgotten anything there is a pre-tinned pair of wires awaiting installation of your favorite connector. 

5-Function Charge Adapter to Male 4mm Bullets (XT60, XT90, EC3, EC5, Deans)

8-Function Charge Adapter to Male 4mm Bullets-300mm Wire 

Racer's Edge provides an ideal solution for enthusiasts with multiple models using batteries with various connectors. This convenient charging squid comes equipped with virtually every possible connector that a modeler may require. Plugs included: Tamiya, Deans, TRX, XT60, JST, EC3, universal receiver pack, and if we've forgotten anything there is a pre-tinned pair of wires awaiting installation of your favorite connector. 

Description:

5-Function Mini/Micro Charge Adapter to Male 4mm Bullets

$3.95 to $5.95

Description:
Our replacement adjustable push rods are as good as any out there at even better prices. Very similar to Hangar 9's Pro-Links, our adjustable push rods offer the ultimate in strength and security with the added bonus of ease of adjust ability and ultra-light weight.

Our Pro-Links have a 4-40 right-hand thread on one side and a 4-40 left-hand thread on the other (turnbuckle). A machined hex in the middle (4mm / 5/32") allows you to make very fine length adjustments without removing the linkage from the servo arm or control horn.

They are also very lightweight, a 110mm (approx. 4.5") linkage weighs just 8 grams but has the strength to lift over 500 pounds. Pro-Links are ideal for any other 4-40 molded ball link or control horn and are available in a variety of sizes. We also have a machined-aluminum wrench that's perfect for making adjustments.


Sizes:

Metric		Approx. US Standard
Non Threaded Length	Entire Rod Including Threads	Non Threaded Length	Entire Rod Including Threads
20mm	45mm	0.79"	1.78"
30mm	55mm	1.18"	2.17"
40mm	65mm	1.57"	2.56"
80mm	110mm	3.15"	4.33"
110mm	140mm	4.33"	5.51"

(Sizes are approximate and can vary between rod length and threads as these are meant to be ADJUSTABLE)


SOLD IN PAIRS