Lemon RX Accessories

Lemon RX Accessories


Products

NEW

Lemon Rx DSMP (DSMX Compatible) 7-Channel Full-Range Telemetry With Diversity Receiver (Energy Meter Optional)

Lemon Rx DSMP (DSMX Compatible) 7-Channel Full-Range Telemetry With Diversity Receiver (Energy Meter Optional)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Description:

Lemon Rx DSMX Compatible 6-Channel Receiver

 

Type: DSMX Compatible Full Range Receiver
Number of Channel: 6
Modulation: DSMX Compatible (Also DSM2 backward Compatible)
Band: 2.4 GHz
Dimension: 25(L) x 18(W) x 11(H)  mm
Weight: 4.5 grams
Voltage Range: 3.45 - 8.4 V

 

Highlight
- FailSafe for all channels via press of a button
- DSMX Satellite port



Understanding the receiver

 

Setup Instruction

Binding

  1. Plug bind plug to the receiver.
  2. Provide power to the unit. LED flashes quickly.
  3. Enable bind mode in transmitter and ensure distance separation of 2 meters from receiver. Solid LED light means binding is completed.
  4. 4) Remove bind plug.

Failsafe Enable (Video showing 10-Channel receiver)

  1. Plug bind plug to the receiver.
  2. Provide power to the unit.
  3. Plug the side pushbutton for memorize current position in Failsafe mode.
  4. Green light will turn on at the bottom of the receiver to indicate Failsafe is successfully enabled.
  5. Remove bind plug

Failsafe Disable 

  1. Rebind the receiver without pressing the side pushbutton will disable the Failsafe mode.
  2. Green light off indicates Failsafe disabled.


 

LM-0051U

$41.99

NEW

Lemon Rx DSMP (DSMX Compatible) 7-Channel Full-Range Telemetry With Diversity Receiver (Energy Meter) XT60 Package

Lemon Rx DSMP (DSMX Compatible) 7-Channel Full-Range Telemetry With Diversity Receiver (Energy Meter) XT60 Package

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Description:

Lemon Rx DSMX Compatible 6-Channel Receiver

 

Type: DSMX Compatible Full Range Receiver
Number of Channel: 6
Modulation: DSMX Compatible (Also DSM2 backward Compatible)
Band: 2.4 GHz
Dimension: 25(L) x 18(W) x 11(H)  mm
Weight: 4.5 grams
Voltage Range: 3.45 - 8.4 V

 

Highlight
- FailSafe for all channels via press of a button
- DSMX Satellite port



Understanding the receiver

 

Setup Instruction

Binding

  1. Plug bind plug to the receiver.
  2. Provide power to the unit. LED flashes quickly.
  3. Enable bind mode in transmitter and ensure distance separation of 2 meters from receiver. Solid LED light means binding is completed.
  4. 4) Remove bind plug.

Failsafe Enable (Video showing 10-Channel receiver)

  1. Plug bind plug to the receiver.
  2. Provide power to the unit.
  3. Plug the side pushbutton for memorize current position in Failsafe mode.
  4. Green light will turn on at the bottom of the receiver to indicate Failsafe is successfully enabled.
  5. Remove bind plug

Failsafe Disable 

  1. Rebind the receiver without pressing the side pushbutton will disable the Failsafe mode.
  2. Green light off indicates Failsafe disabled.


 

LM-0051

$51.99

NEW

Lemon Rx DSMP (DSMX Compatible) 7-Channel Full-Range Telemetry With Diversity Receiver (Vario + Altitude Included. Energy Meter Optional)

Lemon Rx DSMP (DSMX Compatible) 7-Channel Full-Range Telemetry With Diversity Receiver (Vario + Altitude Included. Energy Meter Optional)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Description:

Lemon Rx DSMX Compatible 6-Channel Receiver

 

Type: DSMX Compatible Full Range Receiver
Number of Channel: 6
Modulation: DSMX Compatible (Also DSM2 backward Compatible)
Band: 2.4 GHz
Dimension: 25(L) x 18(W) x 11(H)  mm
Weight: 4.5 grams
Voltage Range: 3.45 - 8.4 V

 

Highlight
- FailSafe for all channels via press of a button
- DSMX Satellite port



Understanding the receiver

 

Setup Instruction

Binding

  1. Plug bind plug to the receiver.
  2. Provide power to the unit. LED flashes quickly.
  3. Enable bind mode in transmitter and ensure distance separation of 2 meters from receiver. Solid LED light means binding is completed.
  4. 4) Remove bind plug.

Failsafe Enable (Video showing 10-Channel receiver)

  1. Plug bind plug to the receiver.
  2. Provide power to the unit.
  3. Plug the side pushbutton for memorize current position in Failsafe mode.
  4. Green light will turn on at the bottom of the receiver to indicate Failsafe is successfully enabled.
  5. Remove bind plug

Failsafe Disable 

  1. Rebind the receiver without pressing the side pushbutton will disable the Failsafe mode.
  2. Green light off indicates Failsafe disabled.


 

LM-0052U

$51.99

NEW

Lemon Rx DSMP (DSMX Compatible) 7-Channel Full-Range Telemetry With Diversity Receiver (Vario + Energy Meter + Altitude) XT60 Package

Lemon Rx DSMP (DSMX Compatible) 7-Channel Full-Range Telemetry With Diversity Receiver (Vario + Energy Meter + Altitude) XT60 Package

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Description:

Lemon Rx DSMX Compatible 6-Channel Receiver

 

Type: DSMX Compatible Full Range Receiver
Number of Channel: 6
Modulation: DSMX Compatible (Also DSM2 backward Compatible)
Band: 2.4 GHz
Dimension: 25(L) x 18(W) x 11(H)  mm
Weight: 4.5 grams
Voltage Range: 3.45 - 8.4 V

 

Highlight
- FailSafe for all channels via press of a button
- DSMX Satellite port



Understanding the receiver

 

Setup Instruction

Binding

  1. Plug bind plug to the receiver.
  2. Provide power to the unit. LED flashes quickly.
  3. Enable bind mode in transmitter and ensure distance separation of 2 meters from receiver. Solid LED light means binding is completed.
  4. 4) Remove bind plug.

Failsafe Enable (Video showing 10-Channel receiver)

  1. Plug bind plug to the receiver.
  2. Provide power to the unit.
  3. Plug the side pushbutton for memorize current position in Failsafe mode.
  4. Green light will turn on at the bottom of the receiver to indicate Failsafe is successfully enabled.
  5. Remove bind plug

Failsafe Disable 

  1. Rebind the receiver without pressing the side pushbutton will disable the Failsafe mode.
  2. Green light off indicates Failsafe disabled.


 

LM-0052

$59.99

NEW

Lemon Rx DSMP/X 7-Channel (End Pin) Stabilizer PLUS With Diversity Antenna (Fully DSMX And DSM2 Compatible)

Lemon Rx DSMP/X 7-Channel (End Pin) Stabilizer PLUS With Diversity Antenna (Fully DSMX And DSM2 Compatible)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Description:

Lemon Rx DSMX Compatible 6-Channel Receiver

 

Type: DSMX Compatible Full Range Receiver
Number of Channel: 6
Modulation: DSMX Compatible (Also DSM2 backward Compatible)
Band: 2.4 GHz
Dimension: 25(L) x 18(W) x 11(H)  mm
Weight: 4.5 grams
Voltage Range: 3.45 - 8.4 V

 

Highlight
- FailSafe for all channels via press of a button
- DSMX Satellite port



Understanding the receiver

 

Setup Instruction

Binding

  1. Plug bind plug to the receiver.
  2. Provide power to the unit. LED flashes quickly.
  3. Enable bind mode in transmitter and ensure distance separation of 2 meters from receiver. Solid LED light means binding is completed.
  4. 4) Remove bind plug.

Failsafe Enable (Video showing 10-Channel receiver)

  1. Plug bind plug to the receiver.
  2. Provide power to the unit.
  3. Plug the side pushbutton for memorize current position in Failsafe mode.
  4. Green light will turn on at the bottom of the receiver to indicate Failsafe is successfully enabled.
  5. Remove bind plug

Failsafe Disable 

  1. Rebind the receiver without pressing the side pushbutton will disable the Failsafe mode.
  2. Green light off indicates Failsafe disabled.


 

LM-0044

$31.99

NEW

Lemon Rx DSMX Compatible (DSM2 Compatible) Full Range Telemetry System (XT60 Package)

Lemon Rx DSMX Compatible (DSM2 Compatible) Full Range Telemetry System (XT60 Package)

 

 

 

 

Description:

Lemon Rx DSMX Compatible 6-Channel Receiver

 

Type: DSMX Compatible Full Range Receiver
Number of Channel: 6
Modulation: DSMX Compatible (Also DSM2 backward Compatible)
Band: 2.4 GHz
Dimension: 25(L) x 18(W) x 11(H)  mm
Weight: 4.5 grams
Voltage Range: 3.45 - 8.4 V

 

Highlight
- FailSafe for all channels via press of a button
- DSMX Satellite port



Understanding the receiver

 

Setup Instruction

Binding

  1. Plug bind plug to the receiver.
  2. Provide power to the unit. LED flashes quickly.
  3. Enable bind mode in transmitter and ensure distance separation of 2 meters from receiver. Solid LED light means binding is completed.
  4. 4) Remove bind plug.

Failsafe Enable (Video showing 10-Channel receiver)

  1. Plug bind plug to the receiver.
  2. Provide power to the unit.
  3. Plug the side pushbutton for memorize current position in Failsafe mode.
  4. Green light will turn on at the bottom of the receiver to indicate Failsafe is successfully enabled.
  5. Remove bind plug

Failsafe Disable 

  1. Rebind the receiver without pressing the side pushbutton will disable the Failsafe mode.
  2. Green light off indicates Failsafe disabled.


 

LM-0030

$49.99

Lemon RX DSMX Compatible 10-Channel (Top Pin) w/ compatible Satellite (DSM2 backward compatible)

 

 

 

 

 

 

 

 

Description:

Lemon Rx DSMX Compatible 10-Channel + Lemon Rx DSMX Compatible Satellite (DSM2 backward compatible)

 

Type: DSMX Compatible 10 Channels Full Range Receiver (Failsafe with UART output)
Number of Channel: 10
Modulation: DSMX Compatible (Also DSM2 backward Compatible)
Band: 2.4 GHz
Dimension: 25(L) x 18(W) x 11(H)  mm
Weight: 12.5 gram without satellite
Voltage Range: 3.45 - 7.2V

 

Binding (1) Setup

1) Insert bind plug to the receiver.
2) Provide power to the unit.
3) Enable bind mode in transmitter and ensure distance separation of 2 meters from receiver.
4) Remove bind plug.

 

Binding (2 - Enable 11ms frame rate for high speed digital servo) Setup
1) Insert 2 bind plug to the receiver binding location.
2) Provide power to the unit.
3) Enable bind mode in transmitter and ensure distance separation of 2 meters from receiver.
4) Remove bind plug.
5) Every time when the units are powered, quickly flashing green light indicates 11ms frame rate is enabled.

Setting Failsafe 
Step 1: Start by binding the receiver to the transmitter in the normal way.
Step 2: Proceed as follows to set failsafe 1) Ensure that transmitter and receiver are turned on. 
2) Insert bind plug into the receiver (Note: to set failsafe, bind plug is applied only when the receiver is turned on).
3) Set transmitter controls to the desired failsafe positions.
4) Press the side pushbutton to memorize failsafe settings.
5) Observe that the green light at the end of the receiver turns on to indicate failsafe is set. (Repeat step 4 will cause the LED to turn off which means failsafe is disabled).
6) Remove bind plug.
7) Disconnect the power for at least 2 seconds and then reconnect the power again.
8) Test failsafe by turning off the transmitter.

--

HUART Output (High speed UART for UAV or quad-flyer application):
TX port (UART, 115200bps, 8N1)
 
Condition 1)       UART output specification when no signal received (device reset and continuously monitor for valid signal roughly about every 0.5 sec):
                                                - <0x13><'R'><'E'><'S'><'E'><'T'><0x13>
                                                - <0x13> is used as header for beginning and ending identifier
 
Condition 2)       UART output specification when signal is received ( updated  ~11ms with 2048/11ms DSM2 protocol with 12 bytes of information):
                                                - <0x13><Throttle><Aileron><Elevator><Rudder><Gear><Aux1><Aux2><Aux3><Aux4><Aux5><0x13>
                                                - DEC(0) ~ DEC(255) refer to the approximate value for each of the full range control output for the channels.
                                                - <0x13> is used as header for beginning and ending identifier

 

--

For example: if all channels are centered except throttle shutdown and AUX is maximized, the UART should output the following.
<0x13><DEC(255)><DEC(127)><DEC(127)><DEC(127)><DEC(127)><DEC(127)><DEC(127)><DEC(127)><DEC(127)><DEC(127)><0x13>

More about failsafe
For Lemon Rx 10 channels receiver, failsafe is available for all channels and some user may found it useful (for robotics application or UAV).

When bind plug is still plugged after successful binding, pressing the mem. button will cause the receiver to memorize all channels settings at the time the button is pressed for use in failsafe. If the failsafe is enabled correctly, green light should be on at the bottom of receiver. Press mem. button again while bind plug is plugged will cause the green light to turn off. This indicate the failsafe mode is disabled. Take the bind plug out before flying!

Even in the event of power disconnected, failsafe settings are still saved and will restore to its functions accordingly when power is provided.

About failsafe enabled:
When the primary receiver and satellite receiver is unable to detect any RF signal for continuous time interval of approximately 3 seconds, all channels will be restored to the saved setting. At this point the receiver will try to find valid RF signal. If valid signal is detected, the receiver will use the valid signal immediately.

If you don't like failsafe, make sure green light is not on before flying!


 

LM-0003

$28.99

NEW

Lemon Rx DSMX Compatible 10-Channel Diversity Antenna Receiver

Lemon Rx DSMX Compatible 10-Channel Diversity Antenna Receiver

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Description:

Lemon Rx DSMX Compatible 6-Channel Receiver

 

Type: DSMX Compatible Full Range Receiver
Number of Channel: 6
Modulation: DSMX Compatible (Also DSM2 backward Compatible)
Band: 2.4 GHz
Dimension: 25(L) x 18(W) x 11(H)  mm
Weight: 4.5 grams
Voltage Range: 3.45 - 8.4 V

 

Highlight
- FailSafe for all channels via press of a button
- DSMX Satellite port



Understanding the receiver

 

Setup Instruction

Binding

  1. Plug bind plug to the receiver.
  2. Provide power to the unit. LED flashes quickly.
  3. Enable bind mode in transmitter and ensure distance separation of 2 meters from receiver. Solid LED light means binding is completed.
  4. 4) Remove bind plug.

Failsafe Enable (Video showing 10-Channel receiver)

  1. Plug bind plug to the receiver.
  2. Provide power to the unit.
  3. Plug the side pushbutton for memorize current position in Failsafe mode.
  4. Green light will turn on at the bottom of the receiver to indicate Failsafe is successfully enabled.
  5. Remove bind plug

Failsafe Disable 

  1. Rebind the receiver without pressing the side pushbutton will disable the Failsafe mode.
  2. Green light off indicates Failsafe disabled.


 

LM-0040

$28.99

Lemon RX DSMX Compatible 6-Channel Receiver

 

 

 

 

Description:

Lemon Rx DSMX Compatible 6-Channel Receiver

 

Type: DSMX Compatible Full Range Receiver
Number of Channel: 6
Modulation: DSMX Compatible (Also DSM2 backward Compatible)
Band: 2.4 GHz
Dimension: 25(L) x 18(W) x 11(H)  mm
Weight: 4.5 grams
Voltage Range: 3.45 - 8.4 V

 

Highlight
- FailSafe for all channels via press of a button
- DSMX Satellite port



Understanding the receiver

 

Setup Instruction

Binding

  1. Plug bind plug to the receiver.
  2. Provide power to the unit. LED flashes quickly.
  3. Enable bind mode in transmitter and ensure distance separation of 2 meters from receiver. Solid LED light means binding is completed.
  4. 4) Remove bind plug.

Failsafe Enable (Video showing 10-Channel receiver)

  1. Plug bind plug to the receiver.
  2. Provide power to the unit.
  3. Plug the side pushbutton for memorize current position in Failsafe mode.
  4. Green light will turn on at the bottom of the receiver to indicate Failsafe is successfully enabled.
  5. Remove bind plug

Failsafe Disable 

  1. Rebind the receiver without pressing the side pushbutton will disable the Failsafe mode.
  2. Green light off indicates Failsafe disabled.


 

LM-0027

$14.95

Lemon RX DSMX Compatible 6-Channel Receiver /Diversity Antenna

 

 

 

 

 

 

 

 

Description:

Lemon Rx DSMX Compatible 6-Channel Receiver with Diversity Antenna

 

Type: DSMX Compatible Full Range Receiver with Diversity Antenna
Number of Channel: 6
Modulation: DSMX Compatible (Also DSM2 backward Compatible)
Band: 2.4 GHz
Dimension: 25(L) x 18(W) x 11(H)  mm
Weight: 4.7 grams
Voltage Range: 3.45 - 8.4 V

 

How dual antennas work

An independent processor monitors an incoming signal and choose the appropriate antenna for reception. This allows 2 different location for installing the antennas along with different orientation. Satellite is no longer needed for receiver diversity. This greatly reduces weight with increased overall reliability in comparison to the use of a primary receiver with satellite receiver.

Photo showing below is the diversity receiver for end-pin stabilizer. The same diversity receiver is also used in this product.

Highlight
True diversity dual antennas with independent processor for monitoring singal on both antennas
- Antennas extended for carbon fuselage / metalic structure installation
- FailSafe for all channels via press of a button
- DSMX Satellite port

Understanding the receiver (Showing DSMX 6-channel non-diversity receiver)


Binding Setup

  1. Plug bind plug to the receiver.
  2. Provide power to the unit. LED flashes quickly.
  3. Enable bind mode in transmitter and ensure distance separation of 2 meters from receiver. Solid LED light means binding is completed.
  4. Remove bind plug.

Failsafe Enable (Video showing 10-Channel receiver)

  1. Plug bind plug to the receiver.
  2. Provide power to the unit.
  3. Plug the side pushbutton for memorize current position in Failsafe mode.
  4. Green light will turn on at the bottom of the receiver to indicate Failsafe is successfully enabled.
  5. Remove bind plug.

     

Failsafe Disable (Video showing 10-Channel receiver)

  1. Rebind the receiver without pressing the side pushbutton will disable the Failsafe mode.
  2. Green light off indicates Failsafe disabled.

 

 

LM-0034

$17.99

Lemon RX DSMX Compatible 6-Channel Receiver w/Satellite

 

 

 

 

 

 

 

 

Description:

Lemon Rx DSMX Compatible 6-Channel Receiver + Lemon DSMX Compatible Satellite

 

Type: DSMX Compatible Full Range Receiver
Number of Channel: 6
Modulation: DSMX Compatible (Also DSM2 backward Compatible)
Band: 2.4 GHz
Dimension: 25(L) x 18(W) x 11(H)  mm
Weight: 4.5 grams + 2.5 grams
Voltage Range: 3.45 - 8.4 V

 

Highlight
- FailSafe for all channels via press of a button
- DSMX Satellite port



Understanding the receiver

 

Setup Instruction

Binding

  1. Plug bind plug to the receiver.
  2. Provide power to the unit. LED flashes quickly.
  3. Enable bind mode in transmitter and ensure distance separation of 2 meters from receiver. Solid LED light means binding is completed.
  4. Remove bind plug.

Setting Failsafe

  1. Start by binding the receiver to the transmitter in the normal way and proceed as follows to set failsafe
  2. Ensure that transmitter and receiver are turned on.
  3. Insert bind plug into the receiver (Note: to set failsafe, bind plug is applied only when the receiver is turned on).
  4. Set transmitter controls to the desired failsafe positions.
  5. Press the side pushbutton to memorize failsafe settings.
  6. Observe that the green light at the end of the receiver turns on to indicate failsafe is set. (Repeat step 4 will cause the LED to turn off which means failsafe is disabled).
  7. Remove bind plug.
  8. Disconnect the power for at least 2 seconds and then reconnect the power again. Test failsafe by turning off the transmitter.

 

LM-0028

$19.99

NEW

Lemon Rx DSMX Compatible 7-Channel (End-Pin) Stabilizer With Diversity Antenna

Lemon Rx DSMX Compatible 7-Channel (End-Pin) Stabilizer With Diversity Antenna

 

 

 

 

 

 

 

 

Description:

Lemon Rx DSMX Compatible 6-Channel Receiver

 

Type: DSMX Compatible Full Range Receiver
Number of Channel: 6
Modulation: DSMX Compatible (Also DSM2 backward Compatible)
Band: 2.4 GHz
Dimension: 25(L) x 18(W) x 11(H)  mm
Weight: 4.5 grams
Voltage Range: 3.45 - 8.4 V

 

Highlight
- FailSafe for all channels via press of a button
- DSMX Satellite port



Understanding the receiver

 

Setup Instruction

Binding

  1. Plug bind plug to the receiver.
  2. Provide power to the unit. LED flashes quickly.
  3. Enable bind mode in transmitter and ensure distance separation of 2 meters from receiver. Solid LED light means binding is completed.
  4. 4) Remove bind plug.

Failsafe Enable (Video showing 10-Channel receiver)

  1. Plug bind plug to the receiver.
  2. Provide power to the unit.
  3. Plug the side pushbutton for memorize current position in Failsafe mode.
  4. Green light will turn on at the bottom of the receiver to indicate Failsafe is successfully enabled.
  5. Remove bind plug

Failsafe Disable 

  1. Rebind the receiver without pressing the side pushbutton will disable the Failsafe mode.
  2. Green light off indicates Failsafe disabled.


 

LM-0033

$29.99