Painted Redwing RC 3d Propeller - White & Red

Description:
High quality 22AWG wire, twisted silicone wire extensions. JR type connections, so they will plug into any receiver/switch, and most servos (Hitec/JR/PowerHD/etc etc....futaba you would have to trim the edge off).
 

• Soft flexible silicone casing
• Heavy duty 22awg
• Universal - XQ Power/Hitec/Power HD/JR/more...
• Reliable! We've NEVER gotten a pair returned
  
  Prices
  • 2" 1 pair - $2.50
  • 2" 2 pair - $4.50
  • 2" 3 pair - $6.99
     
  • 3" 1 pair - $3.50
  • 3" 2 pair - $6.50
  • 3" 3 pair - $8.99
     
  • 6" 1 pair - $3.99
  • 6" 2 pair - $6.99
  • 6" 3 pair - $9.99
     
  • 8" 1 pair - $3.99
  • 8" 2 pair - $6.99
  • 8" 3 pair - $9.99
     
  • 10" 1 pair - $3.99
  • 10" 2 pair - $6.99
  • 10" 3 pair - $9.99
     
  • 12" 1 pair - $4.99
  • 12" 2 pair - $8.99
  • 12" 3 pair - $12.99
     
  • 14" 1 pair - $4.99
  • 14" 2 pair - $8.99
  • 14" 3 pair - $12.99
     
  • 16" 1 pair - $4.99
  • 16" 2 pair - $8.99
  • 16" 3 pair - $12.99
     
  • 18" 1 pair - $6.99
  • 18" 2 pair - $10.99
  • 18" 3 pair - $13.99
    
    
  • 24" 1 pair - $7.99
  • 24" 2 pair - $12.99
  • 24" 3 pair - $15.99
     
  • 28" 1 pair - $7.99
  • 28" 2 pair - $12.99
  • 28" 3 pair - $15.99
     
  • 32" 1 pair - $7.99
  • 32" 2 pair - $12.99
  • 32" 3 pair - $15.99
     
  • 36" 1 pair - $8.99
  • 36" 2 pair - $14.99
  • 36" 3 pair - $17.99
    
    
  • 44" 1 pair - $8.99
  • 44" 2 pair - $14.99
  • 44" 3 pair - $17.99
     
  • 48" 1 pair - $8.99
  • 48" 2 pair - $14.99
  • 48" 3 pair - $17.99
     

Description:

If you want a switch that offers complete dual battery balancing and redundancy with an ultra-small footprint for your scale model then look no further. The new Booma RC intelligent redundant battery balancing switch is the answer.

This switch works with any single or dual battery system. Works with battery chemistry and voltage range from 2.5v to 28v. It comes with a Pin Flag and Ultra Bright Blue LED which can be mounted discretely on your scale model. The Pin Flag controls the internally mounted switch and battery redundancy circuit. The result - beautiful scale appearance with dual battery redundancy peace of mind.

This new balancing technology offers zero voltage drop battery balancing and redundancy which means it can handle huge loads without generating heat. This also means your receiver and servos get all the power unlike conventional battery balancing which loses precious power as heat.

Package Includes:

• 1 x Pin Flag Switch with mounting hardware.

• 1 x Ultra Bright Blue LED with mounting hardware.

• 1 x Dual Battery Balancing power switch circuit.

• 2 x sets of Input and Output JR connectors.

Specs:

• Ultra low foot print for the best scale looks.

• Works with single or dual battery configuration.

• Works with all battery chemistries. LiFe. LiPo, Lion, NiMh, NiCD. Battery voltage range can be from 2.5volts to 28 volts.

• Capable of handling input voltages up to 28volts.

•  Minimal external footprint - All you see on the outside of your model is a 3mm Pin Flag socket and (if required) an ultra-high bright Blue LED. The Pin Flag controls the internal power switch and dual battery redundancy.

• Full Dual Battery Redundancy - If one battery fails the other battery takes full control.

•  Maximum Battery Power Balancing - In a dual battery system HS1 draws current proportionally from both batteries while moving both batteries to a complete load balance situation. This means you get the maximum capacity out of both batteries all the time.

• 2 x 25 amp independent circuits. HS1 is 2 x 25amp circuits into a high power matching battery redundancy circuit. HS1 actually uses 4 x 50 amp rated FET circuits for battery power matching. We passively rate HS1 at 25amps per circuit.

DLE Muffler Extensions

Description:

Choose from 5 sizes!

These extensions fit over the exhaust exits on your DLE muffler. Below are some size dimensions and the muffler that each will fit. It is still a good idea to measure the exits on your muffler.

FORMAT: LxW (width is inside diameter)

A: 63x15 mm : DLE 20RA

B: 64x17 mm : DLE 35RA/40

C: 78x20 mm : DLE 55RA

D: 96x25 mm : DLE 55, DLE 111, DLE 120

E: 121x31 mm : DLE 61, DLE 85

*Sold individually- if you have a twin engine, you will need two extensions

*Each Hose extension comes with a metal clamp to tightly secure it to the muffler.