Switches and Wires

Contact UsCustomer Reviews

Switches and Wires


New Arrivals

more...

Products

Miracle Replacement Switch

Replacement Switch and wire for Miracle switches.

With this switch and wire, you can easily replace a switch in a Miracle RC product. Perfect for if you have a crash and you want to be sure the switch is in perfect working condition. Or if you accidently damage your Miracle switch while working with it.

Just simply unscrew your old Miracle switch, loosen the grub screw that holds the plastic plug, and place the new one in. In about 5 minutes you'll have a brand new conditioned Miracle switch
 

MRC-MS-R

$5.99

Power Switch w/Charge Ports & Fuel Dot

Power Switch w/Charge Ports & Fuel Dot 

Rccskj-switch-FD-3104

$12.99

Smart BUS DB Box

Replacement Switch and wire for Miracle switches.

With this switch and wire, you can easily replace a switch in a Miracle RC product. Perfect for if you have a crash and you want to be sure the switch is in perfect working condition. Or if you accidently damage your Miracle switch while working with it.

Just simply unscrew your old Miracle switch, loosen the grub screw that holds the plastic plug, and place the new one in. In about 5 minutes you'll have a brand new conditioned Miracle switch
 

Rccskj-SBUS-8105

$54.99

Out of stock

MPI Charge Switch with On-board Battery Checker

 

 

 

 

Description:

MPI Charge switch with LED indicator for HiTec and JR leads and on-board battery checker! The three LEDs - green, yellow, & red - monitor the status of the flight pack. It is designed to test the battery under the actual load of the on-board equipment.

The switch is factory preset to 4.8V applications - but for 6V use, simply cut the jumper loop on the back of the switch and seal the wires with silicone glue or tape. The jumper wires can be reconnected for 4.8V operation.

Features:

  • Heavy duty switch and wires
  • Sturdy one-piece design
  • Built-in Redundancy
  • 3-LED on-board battery checker
  • Compatible with 4.8v and 6v Rx packs
  • Easy installation and operation
  • Silicone shock mount included
  • DSC compatible

 

 

MPI-5470

$29.95

Out of stock

3-in-1 UBEC/CDI Kill Switch with Dual LED color Voltage Alarm

Description:
The Optical Kill Switch for gas rc planes, allows you to safely and remotely kill your electronic ignition. It is Fiber Optically Coupled to isolate your ignition system from your radio system so there is NO interference



Features:

  • Includes a remote mountable bright LED to indicate when the ignition is armed.
  • Fiber Optic coupled input/output.
  • Li-Po/Li-lon/A123/Ni-Mh/NiCad Input.
  • Up to 20 Volt 16 amp MOS-FET(IRF7456) output.
  • Low to 3Volt 3amp output.
  • Low Voltage Drop-Less than 150mv.
  • 100% Surface Mount Technology.
  • Heavy Gauge Wires,universal connectors.
  • Small and light weight –only 0.3 OZ!(8g)
  • Reverse Bettery input protection.
  • Shut down the transmitter power or receiver to cut off automatically when kill engine



  •  

RCCSKJ-SW-UBEC-CDI-2122

$19.95

CDI Remote Kill Switch

Description:
The Optical Kill Switch for gas rc planes, allows you to safely and remotely kill your electronic ignition. It is Fiber Optically Coupled to isolate your ignition system from your radio system so there is NO interference



Features:

  • Includes a remote mountable bright LED to indicate when the ignition is armed.
  • Fiber Optic coupled input/output.
  • Li-Po/Li-lon/A123/Ni-Mh/NiCad Input.
  • Up to 20 Volt 16 amp MOS-FET(IRF7456) output.
  • Low to 3Volt 3amp output.
  • Low Voltage Drop-Less than 150mv.
  • 100% Surface Mount Technology.
  • Heavy Gauge Wires,universal connectors.
  • Small and light weight –only 0.3 OZ!(8g)
  • Reverse Bettery input protection.
  • Shut down the transmitter power or receiver to cut off automatically when kill engine




  •  
  •  

RCCSKJ-SW-CDI-Kill-4112

$15.95

Gas Engine Optical Kill Switch

Description:
The Optical Kill Switch for gas rc planes, allows you to safely and remotely kill your electronic ignition. It is Fiber Optically Coupled to isolate your ignition system from your radio system so there is NO interference



Features:

  • Includes a remote mountable bright LED to indicate when the ignition is armed.
  • Fiber Optic coupled input/output.
  • Li-Po/Li-lon/A123/Ni-Mh/NiCad Input.
  • Up to 20 Volt 16 amp MOS-FET(IRF7456) output.
  • Low to 3Volt 3amp output.
  • Low Voltage Drop-Less than 150mv.
  • 100% Surface Mount Technology.
  • Heavy Gauge Wires,universal connectors.
  • Small and light weight –only 0.3 OZ!(8g)
  • Reverse Bettery input protection.
  • Shut down the transmitter power or receiver to cut off automatically when kill engine







  •  
  •  
  •  
  •  
  •  

RCCSKJ-SW-Kill-2117

$15.95

Large Scale Opto Kill for Magneto Engines RCEXL

Description:
The Optical Kill Switch for gas rc planes, allows you to safely and remotely kill your electronic ignition. It is Fiber Optically Coupled to isolate your ignition system from your radio system so there is NO interference



Features:

  • Includes a remote mountable bright LED to indicate when the ignition is armed.
  • Fiber Optic coupled input/output.
  • Li-Po/Li-lon/A123/Ni-Mh/NiCad Input.
  • Up to 20 Volt 16 amp MOS-FET(IRF7456) output.
  • Low to 3Volt 3amp output.
  • Low Voltage Drop-Less than 150mv.
  • 100% Surface Mount Technology.
  • Heavy Gauge Wires,universal connectors.
  • Small and light weight –only 0.3 OZ!(8g)
  • Reverse Bettery input protection.
  • Shut down the transmitter power or receiver to cut off automatically when kill engine



  •  

RCEXL-Opto-kill-magneto

$35.95

Out of stock

RCEXL Optical Kill Switch

Description:
The Optical Kill Switch for gas rc planes, allows you to safely and remotely kill your electronic ignition. It is Fiber Optically Coupled to isolate your ignition system from your radio system so there is NO interference



Features:

  • Includes a remote mountable bright LED to indicate when the ignition is armed.
  • Fiber Optic coupled input/output.
  • Li-Po/Li-lon/A123/Ni-Mh/NiCad Input.
  • Up to 20 Volt 16 amp MOS-FET(IRF7456) output.
  • Low to 3Volt 3amp output.
  • Low Voltage Drop-Less than 150mv.
  • 100% Surface Mount Technology.
  • Heavy Gauge Wires,universal connectors.
  • Small and light weight –only 0.3 OZ!(8g)
  • Reverse Bettery input protection.
  • Shut down the transmitter power or receiver to cut off automatically when kill engine





  •  
  •  
  •  

RCEXL-Opto kill

$15.95

JR Servo Y Extension

Description:
Our 6” heavy-duty Y-harnesses are perfect for standard servos up to 1/4 scale servos. They offer 22awg wire, gold plated connectors and thick wire jackets. Y-junction located in the middle of the harness and is a solid plastic housing rather than the cheaper heat shrink Ys.

Perfect for getting 2 leads out of one RX port.

1 servo Y per unit:

EX-Y-JR

$2.99

RCExl Servo Y

Description:
Our 6” heavy-duty Y-harnesses are perfect for standard servos up to 1/4 scale servos. They offer 22awg wire, gold plated connectors and thick wire jackets. Y-junction located in the middle of the harness and is a solid plastic housing rather than the cheaper heat shrink Ys.

Perfect for getting 2 leads out of one RX port.

1 servo Y per unit:

EX-Y

$3.99

NEW

Shielded Servo Extension

Shielded Servo Extension
Our 6” heavy-duty Y-harnesses are perfect for standard servos up to 1/4 scale servos. They offer 22awg wire, gold plated connectors and thick wire jackets. Y-junction located in the middle of the harness and is a solid plastic housing rather than the cheaper heat shrink Ys.

Perfect for getting 2 leads out of one RX port.

1 servo Y per unit:

MRC-EXT-150mm

$2.99