Power HD Storm-7 Servo - 13kg/cm (180.54 oz/in), 0.055sec - High Voltage

Thought our other servos were great? Well of course they are! But wait until you check out these new Power HD servos - they will rock your wheel pants off* (no wheel pants will be harmed by using this product - but you get the idea).

There's a storm brewing in Redwing RC! These new HD Storms can handle anything thrown at them. Now, we can't imagine your servos heading into battle facing a hurricane or tornado - but they sure behave as if they have fought and conquered the fiercest of storms - taking all of that power and knowledge with them when they are installed into your bird. Rain or shine, these servos are ready for anything!

The HD Storm 5s are high efficiency and perform better. They run cooler and quieter and with less vibration - because there are no brush arcings, the radio frequency interference and electronic noise is significantly reduced.

All aluminum housing, high voltage and the new brushless technology gives you the best strength and speed while being incredibly efficient and long lasting.

New and Improved Technology!

The Power HD Storm 5 high voltage servos are made with brushless technology. Now - we've heard about this "brushless" stuff before but it is time to ask the question on all of our minds - why is that so great? Take a brushless motor for example - no brushes in a brushless motor (no kidding...) nor does it have the commutator - instead a small circuit board coordinates the energy delivery to the windings. Think about this technology being used in a power tool - since the electronics communicate directly with the stationary windings the tool can adapt to its surroundings - only using enough juice necessary to accomplish the job. So if you are using a brushless drill to drive a screw into Styrofoam - it will sense the lack of resistance from the foam and pulls only enough charge from the battery that it needs. Whereas a brushed drill will run as fast and hard as it can no matter the job simultaneously wasting your battery life.

"What the heck does that have to do with my servo?" Well now they are incorporating that smart technology into these HD Storm 5 high voltage servos - so they are not going to be sucking the life of your Redwing LiFe battery when it doesn't have to - which means not only would you be getting a great and powerful servo - it's smart! Your "LiFe" will thank you.

So now the only question is - why are you still reading this? Go buy your Power HD Storm 5 servos before they're gone!

 

Specs:

• Torque:
  • 208.3 oz/in at 6V (15.0 kg/cm)
  • 249.9 oz/in at 7.4V (18.0 kg/cm)
     
• Speed:
  • .085 sec at 6V
  • .066 sec at 7.4V
     
• Voltage: - 6.0 ~ 8.4 V
• Weight: 2.82 oz (80g)
• Size: 1.57 x 0.79 x 1.53 in (40.0 x 20.0 x 38.0mm)
   
• Operating Temp- -20~60centigrade
• Working Frequency - 1520μs / 333hz
• BRUSHLESS Motor
• Double Ball Bearings
• Titanium and Steel gears
• Water resistant O-Rings

Power HD 1370A - Micro Servo - 0.6 kg (8.3 oz/in), .010/sec - 3.7g

The Power-HD DSM44 digital servo is a micro servo with digital control electronics for increased performance. Just like the Power-HD DSP33 ,the DSM44 is also very light and ranks as the secont lightest servo at RedwingRC- weighing only slightly over 6g!!! In the DSM44, the output shaft is supported by a ball bearing for decreased friction, and another great feature is that most of the gears are metal for increased durability! The lead is terminated with a Futaba-compatible standard “JR”-style connector. Servo horns and associated hardware are included.

It is important to note that stalling or back-driving this servo can strip its gears.



Specifications:

• Torque:
  16.66 oz/in at 4.8V (1.2 kg/cm)
  22.21 oz/in at 6V (1.6 kg/cm)
   
• Speed:
  .09 sec at 4.8V
  .07 sec at 6V
   
• Voltage: 4.8v to 6v
• Weight: .24oz (6.75 g)
• Size: .68 x .87 x 1.06in (22 x 8.7 x 27mm
   
• Digital
• Lead Length: 160 mm
• Storage Temperature: -20℃~60℃
• Operating Temperature: -10℃~50℃
• Hardware included
• Suitable for F3P/EPP/KT Airplanes

Power HD 1440A - Micro Servo - 0.8 kg (11.11 oz/in), .09/sec - 4.4g

The Power-HD DSM44 digital servo is a micro servo with digital control electronics for increased performance. Just like the Power-HD DSP33 ,the DSM44 is also very light and ranks as the secont lightest servo at RedwingRC- weighing only slightly over 6g!!! In the DSM44, the output shaft is supported by a ball bearing for decreased friction, and another great feature is that most of the gears are metal for increased durability! The lead is terminated with a Futaba-compatible standard “JR”-style connector. Servo horns and associated hardware are included.

It is important to note that stalling or back-driving this servo can strip its gears.



Specifications:

• Torque:
  16.66 oz/in at 4.8V (1.2 kg/cm)
  22.21 oz/in at 6V (1.6 kg/cm)
   
• Speed:
  .09 sec at 4.8V
  .07 sec at 6V
   
• Voltage: 4.8v to 6v
• Weight: .24oz (6.75 g)
• Size: .68 x .87 x 1.06in (22 x 8.7 x 27mm
   
• Digital
• Lead Length: 160 mm
• Storage Temperature: -20℃~60℃
• Operating Temperature: -10℃~50℃
• Hardware included
• Suitable for F3P/EPP/KT Airplanes

Power HD HD-1711MG Mini Servo - 3.5Kg/cm(48.61 oz/in), 0.11 sec - 17.5g

The Power-HD DSM44 digital servo is a micro servo with digital control electronics for increased performance. Just like the Power-HD DSP33 ,the DSM44 is also very light and ranks as the secont lightest servo at RedwingRC- weighing only slightly over 6g!!! In the DSM44, the output shaft is supported by a ball bearing for decreased friction, and another great feature is that most of the gears are metal for increased durability! The lead is terminated with a Futaba-compatible standard “JR”-style connector. Servo horns and associated hardware are included.

It is important to note that stalling or back-driving this servo can strip its gears.



Specifications:

• Torque:
  16.66 oz/in at 4.8V (1.2 kg/cm)
  22.21 oz/in at 6V (1.6 kg/cm)
   
• Speed:
  .09 sec at 4.8V
  .07 sec at 6V
   
• Voltage: 4.8v to 6v
• Weight: .24oz (6.75 g)
• Size: .68 x .87 x 1.06in (22 x 8.7 x 27mm
   
• Digital
• Lead Length: 160 mm
• Storage Temperature: -20℃~60℃
• Operating Temperature: -10℃~50℃
• Hardware included
• Suitable for F3P/EPP/KT Airplanes

Power HD B5 Brushless Servo - 20.0 kg/cm (277.75 oz/in), 0.066 sec - High Voltage

Description:

Check out the new Power HD 0804HV Brushless servos!

These are great to use a throttle servo and can be used in systems with other high voltage servos!

The Power HD 0804HV high voltage servos are made with brushless technology. Now - we've heard about this "brushless" stuff before but it is time to ask the question on all of our minds - why is that so great? Take a brushless motor for example - no brushes in a brushless motor (no kidding...) nor does it have the commutator - instead a small circuit board coordinates the energy delivery to the windings. Think about this technology being used in a power tool - since the electronics communicate directly with the stationary windings the tool can adapt to its surroundings - only using enough juice necessary to accomplish the job. So if you are using a brushless drill to drive a screw into Styrofoam - it will sense the lack of resistance from the foam and pulls only enough charge from the battery that it needs. Whereas a brushed drill will run as fast and hard as it can no matter the job simultaneously wasting your battery life.

"What the heck does that have to do with my servo?" Well now they are incorporating that smart technology into these HD 0804HV high voltage servos - so they are not going to be sucking the life of your Redwing LiFe battery when it doesn't have to - which means not only would you be getting a great and powerful servo - it's smart! Your "LiFe" will thank you.

These servos are high efficiency and perform better. They run cooler and quieter and with less vibration - because there are no brush arcings, the radio frequency interference and electronic noise is significantly reduced.

All aluminum housing, high voltage and the new brushless technology gives you the best strength and speed while being incredibly efficient and long lasting.

So now the only question is - why are you still reading this? Go buy your Power HD 0804HV servos before they're gone!

 

Specs:

• Torque:
  • 105.54 oz/in at 6V (7.6 kg/cm)
  • 125.00 oz/in at 7.4V (9.0 kg/cm)
     
• Speed:
  • .055 sec at 6V
  • .042 sec at 7.4V
     
• Voltage: 6.0 ~ 7.4 DC Volts
• Weight: 1.58 oz (45g)
• Size: 1.59 x 0.80 x 1.03 in (40.3 x 20.2 x 26.1 mm)
   
• Operating Temp- -20℃~60℃
• Working Frequency - 1520μs / 500hz
• Brushless Motor
• Ball Bearing x 2
• Titanium & Steel Gears

Power HD B7 Revolution (Low Profile) Brushless HV Servo - 13.0 kg/cm (180.54 oz/in), 0.055 sec

Description:

Check out the new Power HD 0804HV Brushless servos!

These are great to use a throttle servo and can be used in systems with other high voltage servos!

The Power HD 0804HV high voltage servos are made with brushless technology. Now - we've heard about this "brushless" stuff before but it is time to ask the question on all of our minds - why is that so great? Take a brushless motor for example - no brushes in a brushless motor (no kidding...) nor does it have the commutator - instead a small circuit board coordinates the energy delivery to the windings. Think about this technology being used in a power tool - since the electronics communicate directly with the stationary windings the tool can adapt to its surroundings - only using enough juice necessary to accomplish the job. So if you are using a brushless drill to drive a screw into Styrofoam - it will sense the lack of resistance from the foam and pulls only enough charge from the battery that it needs. Whereas a brushed drill will run as fast and hard as it can no matter the job simultaneously wasting your battery life.

"What the heck does that have to do with my servo?" Well now they are incorporating that smart technology into these HD 0804HV high voltage servos - so they are not going to be sucking the life of your Redwing LiFe battery when it doesn't have to - which means not only would you be getting a great and powerful servo - it's smart! Your "LiFe" will thank you.

These servos are high efficiency and perform better. They run cooler and quieter and with less vibration - because there are no brush arcings, the radio frequency interference and electronic noise is significantly reduced.

All aluminum housing, high voltage and the new brushless technology gives you the best strength and speed while being incredibly efficient and long lasting.

So now the only question is - why are you still reading this? Go buy your Power HD 0804HV servos before they're gone!

 

Specs:

• Torque:
  • 105.54 oz/in at 6V (7.6 kg/cm)
  • 125.00 oz/in at 7.4V (9.0 kg/cm)
     
• Speed:
  • .055 sec at 6V
  • .042 sec at 7.4V
     
• Voltage: 6.0 ~ 7.4 DC Volts
• Weight: 1.58 oz (45g)
• Size: 1.59 x 0.80 x 1.03 in (40.3 x 20.2 x 26.1 mm)
   
• Operating Temp- -20℃~60℃
• Working Frequency - 1520μs / 500hz
• Brushless Motor
• Ball Bearing x 2
• Titanium & Steel Gears

Heavy Duty 25T Metal Aluminum Servo Arm (Futaba, Savox, Power HD)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Description:

Thought our other servos were great? Well of course they are! But wait until you check out these new Power HD servos - they will rock your wheel pants off* (no wheel pants will be harmed by using this product - but you get the idea).

There's a storm brewing in Redwing RC! These new HD Storms can handle anything thrown at them. Now, we can't imagine your servos heading into battle facing a hurricane or tornado - but they sure behave as if they have fought and conquered the fiercest of storms - taking all of that power and knowledge with them when they are installed into your bird. Rain or shine, these servos are ready for anything!

The HD Storm 3s are high efficiency and perform better. They run cooler and quieter and with less vibration - because there are no brush arcings, the radio frequency interference and electronic noise is significantly reduced.

All aluminum housing, high voltage and the new brushless technology gives you the best strength and speed while being incredibly efficient and long lasting.

New and Improved Technology!

The Power HD Storm 3 high voltage servos are made with brushless technology. Now - we've heard about this "brushless" stuff before but it is time to ask the question on all of our minds - why is that so great? Take a brushless motor for example - no brushes in a brushless motor (no kidding...) nor does it have the commutator - instead a small circuit board coordinates the energy delivery to the windings. Think about this technology being used in a power tool - since the electronics communicate directly with the stationary windings the tool can adapt to its surroundings - only using enough juice necessary to accomplish the job. So if you are using a brushless drill to drive a screw into Styrofoam - it will sense the lack of resistance from the foam and pulls only enough charge from the battery that it needs. Whereas a brushed drill will run as fast and hard as it can no matter the job simultaneously wasting your battery life.

"What the heck does that have to do with my servo?" Well now they are incorporating that smart technology into these HD Storm 3 high voltage servos - so they are not going to be sucking the life of your Redwing LiFe battery when it doesn't have to - which means not only would you be getting a great and powerful servo - it's smart! Your "LiFe" will thank you.

So now the only question is - why are you still reading this? Go buy your Power HD Storm 3 servos before they're gone!

 

Specs:

• Torque:
  • 374.9 oz/in at 6V (27.0 kg/cm)
  • 444.4 oz/in at 7.4V (32.0 kg/cm)
     
• Speed:
  • .14 sec at 6VV
  • .11 sec at 7.4V
     
• Voltage: 6.0 ~ 8.4 V
• Weight: 2.82 oz (80g)
• Size: 1.57 x 0.79 x 1.53 in (40.0 x 20.0 x 38.0mm)
   
• Operating Temp- -20~60centigrade
• Working Frequency - 1520μs / 333hz
• BRUSHLESS Motor
• Double Ball Bearings
• Titanium and Steel gears
• Water resistant O-Rings

 

Power HD LW-25MG Waterproof Servo - 25Kg/cm (347.2 oz/in), 0.14sec 72 grams

Specifications:

• Modulation: Digital
• Gear Type: Metal Geared
• Torque: 6v - 222.2 oz-in (16 kg-cm), 4.8v - 180.5 oz-in (13 kg-cm)
• Speed: 6v - .18 sec/60deg., 4.8v - .20 sec/60deg.

 

 

 

TEMPORARILY OUT OF STOCK! New stock returning in 2-3 weeks - pre order and we will ship out AS SOON as they arrive!

 

 

 

Power HD LW-30MG Waterproof Crawler Servo - 30Kg/cm (416.6 oz/in), 0.14sec 

Specifications:

• Modulation: Digital
• Gear Type: Metal Geared
• Torque: 6v - 222.2 oz-in (16 kg-cm), 4.8v - 180.5 oz-in (13 kg-cm)
• Speed: 6v - .18 sec/60deg., 4.8v - .20 sec/60deg.

 

 

 

TEMPORARILY OUT OF STOCK! New stock returning in 2-3 weeks - pre order and we will ship out AS SOON as they arrive!

 

 

 

Power HD LW-20MG Waterproof Crawler Servo - 20Kg/cm (277.7 oz/in), 0.16sec 

Specifications:

• Modulation: Digital
• Gear Type: Metal Geared
• Torque: 6v - 222.2 oz-in (16 kg-cm), 4.8v - 180.5 oz-in (13 kg-cm)
• Speed: 6v - .18 sec/60deg., 4.8v - .20 sec/60deg.

 

 

 

TEMPORARILY OUT OF STOCK! New stock returning in 2-3 weeks - pre order and we will ship out AS SOON as they arrive!

 

 

 

Power HD LW-15MG Waterproof Crawler Servo - 15Kg/cm (208.3 oz/in), 0.11sec  

Specifications:

• Modulation: Digital
• Gear Type: Metal Geared
• Torque: 6v - 222.2 oz-in (16 kg-cm), 4.8v - 180.5 oz-in (13 kg-cm)
• Speed: 6v - .18 sec/60deg., 4.8v - .20 sec/60deg.

 

 

 

TEMPORARILY OUT OF STOCK! New stock returning in 2-3 weeks - pre order and we will ship out AS SOON as they arrive!

 

 

 

Power HD 1250MG Mini Servo - 3.5Kg/cm(48.61 oz/in), 0.12 sec - 25.0g 

The Power-HD DSM44 digital servo is a micro servo with digital control electronics for increased performance. Just like the Power-HD DSP33 ,the DSM44 is also very light and ranks as the secont lightest servo at RedwingRC- weighing only slightly over 6g!!! In the DSM44, the output shaft is supported by a ball bearing for decreased friction, and another great feature is that most of the gears are metal for increased durability! The lead is terminated with a Futaba-compatible standard “JR”-style connector. Servo horns and associated hardware are included.

It is important to note that stalling or back-driving this servo can strip its gears.



Specifications:

• Torque:
  16.66 oz/in at 4.8V (1.2 kg/cm)
  22.21 oz/in at 6V (1.6 kg/cm)
   
• Speed:
  .09 sec at 4.8V
  .07 sec at 6V
   
• Voltage: 4.8v to 6v
• Weight: .24oz (6.75 g)
• Size: .68 x .87 x 1.06in (22 x 8.7 x 27mm
   
• Digital
• Lead Length: 160 mm
• Storage Temperature: -20℃~60℃
• Operating Temperature: -10℃~50℃
• Hardware included
• Suitable for F3P/EPP/KT Airplanes