a small package. Check out the videos and specs of the Mobula 7 by HappyModel below!
Features:
Specifications:
Note: This BNF version comes without a transmitter radio (remote controller).
Compatible with DSM2/DSMX radios or our Multi-Protocal Jumper T-16 radio-- Jumper T16 Open Scource Mutli-Protocal Radio
**Special Quad/Radio Combo offer $40 off when purchased together!**
Package list:
1x Mobula7 75mm FPV Drone
4x 40mm 3-Blade Propellers ( 4 CW & 4 CCW)
2x 3.8v 250mah 30C/60C Lipo battery
1x USB Lipo/LIHV Charger
1x Fixing Mount for Lipo Battery
1x Propeller Disassemble Tool
1x Screwdriver
Tuning your Mobula7:
Your Mobula7’s flight controller controls its flight through settings known as PIDS. Changing these changes the characteristics
of your quad’s flight. RWRC’s recommended Mobula7 tune is:
set p_pitch = 65
set i_pitch = 80
set d_pitch = 50
set f_pitch = 96
set p_roll = 65
set i_roll = 80
set d_roll = 50
set f_roll = 96
set p_yaw = 65
set i_yaw = 75
set d_yaw = 0
set f_yaw = 100
To setup this tune, connect your Mobula7 to betaflight and click the CLI tab. Copy and paste the above settings in, hit enter,
type save, then hit enter again. Enjoy your Mobula’s improved flight characteristics!
The new betaflight configurator 10.5.0 and 10.5.1 are not compatible with Mobula7 and Mobula7 HD for now.
HappyModel suggests using Betaflight configurator 10.4.0
Crazybee F3 Pro Flight Controller | Item Name: Crazybee F3 Pro FC MCU: STM32F303CCT6 (72MHZ, 256K FLASH) Sensor: MPU-6000(SPI connection) Board size: 28.5 * 28.5MM Power supply: 1-2S battery input (DC 3.5-8.7V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Receiver ( Different version having different receiver) Built-in Betaflight OSD(SPI Control) Built-in Current meter Max 28A Current meter scale set to 1175 Built-in 5V 1A BEC with LC filter Built-in voltage detection BLHELI_S pass-through Ready Heading LED Ready Firmware (Frsky version) CRAZYBEEF3 PRO FR Firmware target: CrazybeeF3FR (Flysky version) CRAZYBEEF3 PRO FS Firmware target: CrazybeeF3FS (DSM2/DSMX version) CRAZYBEEF3 PRO Firmware target: CrazybeeF3DX (Frsky EU-LBT version) CRAZYBEEF3 PRO FS Firmware target: CrazybeeF3FS |
Onboard 5A 4 In 1 ESC | Power supply: 1-2S LiPo/LiPo HV (3.5v/8.7v) |
Onboard Frsky NON-EU receiver Version | SPI BUS receiver Frsky D8/D16 switchable Compatible Non EU transmitter both D8 and D16 mode Channels: 8ch or 16ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 300m |
Onboard Frsky EU-LBT Version (External XM+ receiver) | Operating Voltage Range: 3.7~10V |
Onboard Flysky receiver Version | SPI BUS receiver Protocol: AFHDS and AFHDS-2A Switchable Channels: 8ch(AFHDS) or 14ch(AFHDS-2A) Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 300m |
Onboard DSM2 / DSMX receiver version | Serial bus receiver Protocol: DSM2/DSMX compatible Channels:6-9 (Depend on your radio) No ground interference ( Transmitter and receiver 1 m from the ground): 300m |
SE0802 16000KV Motor | Model: SE0802 KV: 16000KV Configu-ration: 9N12P Stator Diamter: 8mm Stator Length: 2mm Shaft Diameter: Φ1.0 Motor Dimension (Dia.*Len) : Φ10.5*14.5mm Weight: 1.8g Support 1-2S Lipo No.of Cells: 1S Lipo |
Propeller | 40mm 4-blade Propeller ( 4 CW + 4 CCW) |
5.8G VTX AIO Camera | 5.8G 40CH 25mW VTX Output power: 25mw Frequency: 40CH Input voltage: 3.3V 5.5V Current consumption: 300mA(type) 700TVL FOV120 Camera Camera resolution: 700TVL Field of view: 120° Video Format: NTSC Antenna: RG178 antenna Frequency: 5.8GHz 5bands 40 channels With Raceband Smartaudio ready(Frsky EU-LBT and DSMX version not compatible) Size: 13.9"12.0mm ( L*W ) Weight: 3g |
Lipo Battery | Capacity:250mAh Voltage:3.8v Continuous Discharge Rate: 30C Instantaneous discharge rate: 60C Size: 55mmx12mmx7mm Weight: 6.5g Connector: PH2.0 Notes: Need 2pcs batteries for Series circuit |