CDI Remote Kill Switch

Contact UsCustomer Reviews

CDI Remote Kill Switch

Our Price:

$17.99


Quantity (4)

Availability 4 in stock
Weight 0.19 lbs
SKU RCCSKJ-SW-CDI-Kill-4112

Description: CDI Remote Kill Switch
This Remote CDI Kill Switch for Gas RC planes, allows you to safely and remotely kill your electronic ignition. It is Fiber Optically Coupled providing complete isolation between the ignition system and the radio system so there is NO interference. Simply plug in the JR lead labeled To Receiver into a spare receiver channel and the other leads to the battery and ignition to give the pilot the ability to safely kill the engine anytime on the ground or in the air.  This is a must have safety device for any gas powered plane (most fields require a kill switch for gas planes).

Features:

  • Integrated CDI remote kill switch, allows pilot to kill engine anytime on the ground or in the air
  • Fiber Optic coupled input/output to the CDI provide complete isolation between the receiver power and CDI power to prevent high-frequency interference
  • Dual LED lights indicate the input and output power status.
  • Applies to lithium, nickel metal hydride, nickel cadmium, and A123 batteries powered directly
  • Can be used for other purposes such as: control pull smoke detectors, retractable landing gear, ignite fireworks, drop parachute, etc…

Technical Parameters:

  • Voltage: 4.8-13V
  • Current: 0-3A
  • Weight: 11g
  • Size: 30 x 24 x 9mm
: *
: *
: *
 

Bob Smith Industries Insta-Cure Super Thin CA

Untitled Document

Description:

Bob Smith Industries CA Glue

Insta-Cure™

Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond.

Works Best On:

  • Balsa Wood
  • Ceramics

Works Good On:

  • Soft Wood
  • Fiberglass
  • Hard Plastics
  • Water-Resistant
  • CA Hinges

 

Avaliable in 2oz and 3/4 Pocket Size.

Pocket CAs feature a new top that has a pin built into the cap that covers the nozzle. This pin seals the bottle so that if it is tipped over, the bottle will not leak. This makes the Pocket CAs ideal for keeping in your tool or field box, just like our IC-Gel. One disadvantage that the new Pocket CA top has is the bluntness of the nozzle. This makes it more difficult to apply small amounts of the CA, especially in tight places. From the feedback we have received, it appears about 25-30% of users prefer the new Pocket CA top, which means that over 70% prefer our standard top for general bonding purposes. Most users are buying both types. Our original top for the workshop, and the Pocket CA for use out in the field. The 3/4 oz. Pocket CAs are available in BSI's Insta-Cure, Insta-Cure+, Maxi-Cure and Super-Gold+. BSI's new extender tip #304 works on the Pocket CA.

 

Click to Download Safety Data Sheet

 

 

 

BSI-CA-

$4.99

Bob Smith Industries Insta-Cure+ Gap Filling CA

Untitled Document

Description:

Bob Smith Industries CA Glue

Insta-Cure+™ Super Glue, CA

Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out.

Directions:

Unscrew top from nozzle. For finer applications, use the extender tip. Apply Insta-Cure+™ CA to one side of the parts being joined, then hold them tightly together for 5-15 seconds. For larger bonding areas, apply serpentine beads of the CA with enough spacing to allow for the spreading of the adhesive. Insta-Set™ accelerator can be sprayed to cure the CA that oozes from joints. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220° F. Soak extender tip in acetone for cleaning

 

Works Best On:

  • Balsa Wood
  • Soft Wood

Works Good On:

  • Hard Wood
  • Glass & Metals
  • Fiberglass
  • Ceramics
  • Hard Plastics
  • Rubber
  • Laminating
  • Water-Resistant
  • Reinforcing

 

Avaliable in 2oz and 3/4 Pocket Size.

Pocket CAs feature a new top that has a pin built into the cap that covers the nozzle. This pin seals the bottle so that if it is tipped over, the bottle will not leak. This makes the Pocket CAs ideal for keeping in your tool or field box, just like our IC-Gel. One disadvantage that the new Pocket CA top has is the bluntness of the nozzle. This makes it more difficult to apply small amounts of the CA, especially in tight places. From the feedback we have received, it appears about 25-30% of users prefer the new Pocket CA top, which means that over 70% prefer our standard top for general bonding purposes. Most users are buying both types. Our original top for the workshop, and the Pocket CA for use out in the field. The 3/4 oz. Pocket CAs are available in BSI's Insta-Cure, Insta-Cure+, Maxi-Cure and Super-Gold+. BSI's new extender tip #304 works on the Pocket CA.

 

Click to Download Safety Data Sheet

 

 

 

 

BSI-CA-56b908caadc59

$4.99

HV Dual Charging Switch (Futaba/JR Connector)

HV Dual Charging Switch (Futaba/JR Connector)

Rccskj-Dual-HV-switch-2111

$19.99