General Accessories

XT30 Connectors

Nylon T-connectors. These are VERY similar to Dean's style T connectors, and are fully compatible with Deans connectors.
Pack includes 5 male and 5 female connectors.



These connectors are made from Nylon, making them very tough and difficult to melt, even with the worst of soldering skills.

Features:

• Durable nylon connectors
• Compatible with Deans large connectors
• Easy to solder
• Positive/negative can only connect one way ensuring proper polarity

PRICE FOR PACKS OF 5 PAIR

Description:
10 pack of servo safety clips. Made to retain your servo wires to keep them from slipping off during flight.

A must have to to ensure your servo connectors stay securely connected.

Packs of 10:

Hall Sensor Tester, Rcexl Gas Engine CDI Ignition Tester

This is a timing and testing kit for RC gas engines.

This kit will allow you to check the working condition of your ignition without needing to restart the engine.

Analog engine speeds between 400 RPM ~ 20000 RPM can be used to check for interferences and radio range check.

An LED will light up when everything is working properly.

Description:
With this Redwing RC Turnbuckle wrench, you can adjust your pushrods that come with our kits with ease.

This wrench is designed to give you easy access and movement to quickly and easily adjust your pushrods.

Both openings are 4mm so it will adjust our pushrods or ANY pushrods that are appx 4mm or 5/32 inches.

$3.95 to $5.95

Description:
Our replacement adjustable push rods are as good as any out there at even better prices. Very similar to Hangar 9's Pro-Links, our adjustable push rods offer the ultimate in strength and security with the added bonus of ease of adjustability and ultra-light weight.

Our Pro-Links have a 4-40 right-hand thread on one side and a 4-40 left-hand thread on the other (turnbuckle). A machined hex in the middle (4mm / 5/32") allows you to make very fine length adjustments without removing the linkage from the servo arm or control horn.

They are also very lightweight, a 110mm (approx. 4.5") linkage weighs just 8 grams but has the strength to lift over 500 pounds. Pro-Links are ideal for any other 4-40 molded ball link or control horn and are available in a variety of sizes. We also have a machined-aluminum wrench that's perfect for making adjustments.


Sizes:

(Sizes are approximate and can vary between rod length and threads as these are meant to be ADJUSTABLE)


SOLD IN PAIRS
 

Description:

With the Miracle RC prop reamer you can increase the diameter of the hole in your prop while keeping it true and square.

The Miracle prop reamer cuts in increments of 5mm, 1/4", 5/16", 3/8"

The Miracle prop reamer is made of a harder steel than most to stay strong for MANY cuts for many years.

Miracle RC Belly stand for your Radio

Replacement Switch and wire for Miracle switches.

With this switch and wire, you can easily replace a switch in a Miracle RC product. Perfect for if you have a crash and you want to be sure the switch is in perfect working condition. Or if you accidently damage your Miracle switch while working with it.

Just simply unscrew your old Miracle switch, loosen the grub screw that holds the plastic plug, and place the new one in. In about 5 minutes you'll have a brand new conditioned Miracle switch
 

Available in styles for

• Yak carbon fiber replacement gear Sbach carbon fiber replacement gear MXSR/MX2 carbon fiber replacement gear Extra carbon fiber replacement gear Edge carbon fiber replacement gear etc
  
  A - Sbach, MXSR, Slick, Edge, Extra 260
  B - Yak, Sukoi
  C - Yak also
  PLEASE NOTE: THE GEAR HAVE NOT BEEN DRILLED SO YOU CAN MATCH IT TO YOUR PLANE.

Dimensions (match the below information to the inset photo)

• 30cc A STYLE (3.6 oz)
  • A=7.5"
  • B=16"
  • C=5.5"
  • D=1.187" taper to 1"
  • E=1.5"

• 30cc B STYLE (3.8 oz)
  • A=6.5"
  • B=16.75"
  • C=6.25"
  • D=1.375" taper to 1"
  • E=1"

• 30cc C STYLE (3.4 oz)
  • A=6.5"
  • B=15.5"
  • C=5.5"
  • D=1.125" taper to .75
  • E=1"

• 50cc A STYLE (8.2 oz)
  • A=9.25"
  • B=18.75"
  • C=8"
  • D=1.5" taper to 1.125"
  • E=1.5"

• 50cc B STYLE (6 oz)
  • A=8.75"
  • B=18.5"
  • C=6.5"
  • D=1.5" taper to 1"
  • E=1.25"

• 50cc C STYLE (6 oz)
  • A=7.75"
  • B=18.5"
  • C=6.25"
  • D=1.5" taper to 1"
  • E=1.0"

• 50cc A STYLE (8.2 oz)
  • A=9.25"
  • B=18.75"
  • C=8"
  • D=1.5" taper to 1.125"
  • E=1.5"

• 50cc B STYLE (6 oz)
  • A=8.75"
  • B=18.5"
  • C=6.5"
  • D=1.5" taper to 1"
  • E=1.25"

Carbon Fiber Landing Gear Extra 300 Series For 26-30cc, 50-80cc and 100-120cc 

Dimensions (match the below information to the inset photo)

• 26-30cc 
  • A=140mm 5.5"
  • B=400mm 15.75"
  • C=170mm 6.69"
  • D=28mm 1.10" 

• 50-80cc 
  • A=160mm 6.29"
  • B=465mm 18.30"
  • C=198mm 7.79"
  • D=40mm 1.57" 

• 100-120cc 
  • A=190mm 7.48"
  • B=560mm 22.04"
  • C=252mm 9.92"
  • D=50mm 1.96" 

Heat shrink covering for RC planes

Please contact us for information on if your plane is using Ultracote, or TruCote before ordering if you are unsure

Description:
TruCote covering is a high tech polyester covering that is sensative to heat which makes it easy to apply to your plane. It offers high adhesion, fuel proof/waterproof covering for your plane. Easy to apply using a heat gun and/or iron.
 

• Specs:
• Width: 23.5”
• Temp to adhesion: Approximately 250 degrees F
• Shrinkage begins: Approximately 275 degrees F
• Maximum recommended temp: Approximately 300 degrees F

For instructions on how to apply covering here is a helpful tutorial:

http://www.rc-airplane-advisor.com/heat-shrink-covering.html


Sold in 1 Foot Sections. Please select how many feet you want.

Please put what plane this is for at checkout so that we can match it!

Description:
The Miracle RC, CDI Shock Stand is made to prevent damage to your CDI/Ignition system, by abosorbing harmful vibrations caused by your engine. The Miracle RC CDI Shock Stand can also help to prevent damage from crashes or hard landings. The Shock Stand is made of light weight high quality annodized aluminum. Included with the Miracle Shock Stand are all the accessories you will need to properly mount your ignition and stand, such as a velcro strap, spare hook and loop, screws, washers etc.



Specifications:

• Weight:
• Dimensions appx: 90mm x 57mm

Includes:

• Stand
• Velcro Strap
• Mounting Washers
• Self adhesive velcro
• screws

This package of 10 Pin Hinges are high quality steel pin hinges desinged to join your surfaces with strong free momvement. Built in the "Robart" style of hinge, they are strong and light and offer a high quality connection to your moving surfaces for 20cc or bigger planes

These hinges will install by drilling a 3/16" hole and inserting the hinge with a bit of glue.

---

Check out these Videos: