Glue, Oil and Cleaners

Contact UsCustomer Reviews

Glue, Oil and Cleaners

Glue, Oil and Cleaners
Redwing RC complete line of Adhesives, Oil and Cleaners for all your RC needs!

Products

Red Line Synthetic Oil

Description:

Finally you have somewhere you can get Red Line's Synthetic 2-Stroke oil! The owner of Redwing RC has been suggesting it to you for a long time and now you can finally experience this great quality oil for your engine with super convenience.

You won't find a smoother, cleaner and better lubricating oil out there for the price. It's the only one Redwing trusts to fuel their birds!

It contains ester base oils with the highest film strength and affinity for hot metal,provides the lubricating qualities of castors, but with exceptional cleanliness (less grease!) and the LOW carbon residue dramatically reduces plug fouling and smoke. It's also compatible with reformulated fuels and each product works in both premix or injection systems. Sounds great, right?! We definitely think so.

Suggested ratio is 50:1 but is useful up to 100:1 depending on operating conditions.

Dyno proven for gains of 3-5% and more power over longer runs, High-temp stability prevents deposits on combustion chambers, exhaust ports, upper ring, and piston crown!

Wow.. what more could we really offer you? What are you waiting for? no more running bad quality oil through your shiny engines - pick up Red Line oil from Redwing RC today for LESS!

_____

Features:

  • Provides conventional motor oils with antiwear additives like zinc and phosphorus (ZDDP) necessary to protect against camshaft and valve train damage on break-in
  • Allow pistons rings to seat properly with less-slick oil, while antiwear additives protect other engines components to avoid excessive wear
  • Can also be used in conventional and synthetic oils during regular operation, providing an extra package of protection otherwise not found in most motor oils
  • 16oz bottle treats up to 12 quarts of motor oil--in many cases, one bottle can serve two engines or oil changes

 

More Info:

  • Reformulated for improved frictional properties
  • Special detergents for improved lubricity and less detonation
  • Polyol ester base stocks provide more stability and film strength when exposed to excess fuel dilution
  • Each of these products has no less than 2200ppm of zinc and phosphorus for antiwear
  • Each race oil product is a multi-grade, offering 2-4% more power than oil of a similar viscosity - 20WT is a 5W20, 30WT is a 10W30, 40WT is a 15W40, 50WT is a 15W50
  • Improved protection at startup, lower oil temp, cleanliness
  • Remember to change these oils more frequently than regular motor oils

 

Technical Information:

Increases antiwear level per quart when using One Bottle (16oz.):

Capacity - Phosphorus - Zinc
15 quarts - 610 ppm - 736 ppm
12 quarts - 763 ppm - 920 ppm
10 quarts - 915 ppm - 1104 ppm
8 quarts - 1145 ppm - 1380 ppm
7 quarts - 1307 ppm - 1577 ppm
6 quarts - 1525 ppm - 1840 ppm
5 quarts - 1830 ppm - 2208 ppm
4 quarts - 2288 ppm - 2760 ppm
1 quart - 9160 ppm - 11040 ppm

Half Bottle (8oz.) when treating:

Capacity - Phosphorus - Zinc
12 quarts - 382 ppm - 460 ppm
10 quarts - 458 ppm - 552 ppm
8 quarts - 572 ppm - 690 ppm
6 quarts - 763 ppm - 920 ppm
5 quarts - 915 ppm - 1104 ppm
4 quarts - 1145 ppm - 1380 ppm

One Quarter Bottle (4oz) when treating:

Capacity - Phosphorus - Zinc
6 quarts - 382 ppm - 460 ppm
5 quarts - 458 ppm - 552 ppm
4 quarts - 572 ppm - 690 ppm
3 quarts - 763 ppm - 920 ppm


Bottle (16oz) contains: 
33.8 grams total ZDDP (zinc dialkyldithiophosphate)
17,000 ppm, 7.8 grams Phosphorus (P)
20,500 ppm, 9.4 grams Zinc (Zn)
16.6 grams Sulphur (S)

_____
Available in 16oz

Download Safety Data Sheet Here

RL-Oil-1gal

$125.00

Bob Smith Industries Insta-Cure Super Thin CA

Untitled Document

Description:

Bob Smith Industries CA Glue

Insta-Cure™

Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond.

Works Best On:

  • Balsa Wood
  • Ceramics

Works Good On:

  • Soft Wood
  • Fiberglass
  • Hard Plastics
  • Water-Resistant
  • CA Hinges

 

Avaliable in 2oz and 3/4 Pocket Size.

Pocket CAs feature a new top that has a pin built into the cap that covers the nozzle. This pin seals the bottle so that if it is tipped over, the bottle will not leak. This makes the Pocket CAs ideal for keeping in your tool or field box, just like our IC-Gel. One disadvantage that the new Pocket CA top has is the bluntness of the nozzle. This makes it more difficult to apply small amounts of the CA, especially in tight places. From the feedback we have received, it appears about 25-30% of users prefer the new Pocket CA top, which means that over 70% prefer our standard top for general bonding purposes. Most users are buying both types. Our original top for the workshop, and the Pocket CA for use out in the field. The 3/4 oz. Pocket CAs are available in BSI's Insta-Cure, Insta-Cure+, Maxi-Cure and Super-Gold+. BSI's new extender tip #304 works on the Pocket CA.

 

Click to Download Safety Data Sheet

 

 

 

BSI-CA-131

$4.99

Bob Smith Industries Insta-Cure+ Gap Filling CA

Untitled Document

Description:

Bob Smith Industries CA Glue

Insta-Cure+™ Super Glue, CA

Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out.

Directions:

Unscrew top from nozzle. For finer applications, use the extender tip. Apply Insta-Cure+™ CA to one side of the parts being joined, then hold them tightly together for 5-15 seconds. For larger bonding areas, apply serpentine beads of the CA with enough spacing to allow for the spreading of the adhesive. Insta-Set™ accelerator can be sprayed to cure the CA that oozes from joints. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220° F. Soak extender tip in acetone for cleaning

 

Works Best On:

  • Balsa Wood
  • Soft Wood

Works Good On:

  • Hard Wood
  • Glass & Metals
  • Fiberglass
  • Ceramics
  • Hard Plastics
  • Rubber
  • Laminating
  • Water-Resistant
  • Reinforcing

 

Avaliable in 2oz and 3/4 Pocket Size.

Pocket CAs feature a new top that has a pin built into the cap that covers the nozzle. This pin seals the bottle so that if it is tipped over, the bottle will not leak. This makes the Pocket CAs ideal for keeping in your tool or field box, just like our IC-Gel. One disadvantage that the new Pocket CA top has is the bluntness of the nozzle. This makes it more difficult to apply small amounts of the CA, especially in tight places. From the feedback we have received, it appears about 25-30% of users prefer the new Pocket CA top, which means that over 70% prefer our standard top for general bonding purposes. Most users are buying both types. Our original top for the workshop, and the Pocket CA for use out in the field. The 3/4 oz. Pocket CAs are available in BSI's Insta-Cure, Insta-Cure+, Maxi-Cure and Super-Gold+. BSI's new extender tip #304 works on the Pocket CA.

 

Click to Download Safety Data Sheet

 

 

 

 

BSI-CA-133

$4.99

Bob Smith Industries Maxi-Cure Exra Thick CA

Untitled Document

Description:

Bob Smith Industries CA Glue

Maxi-Cure™ Super Glue, CA

Maxi-Cure™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE™ bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, clothtextured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE™ or any other adhesive. It also is best for bonding the tires for R/C cars.

Directions:

Unscrew top from nozzle. For finer applications, use the extender tip. Apply Maxi-Cure™ CA to one side of the parts being joined, then hold them tightly to- gether for 10-20 seconds. For larger bonding areas, apply serpentine beads of the CA with enough spacing to allow for the spreading of the adhesive. Insta-Set™ accelerator can be sprayed to cure the CA that oozes from joints. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220° F. Soak extender tip in acetone for cleaning.

 

Works Best On:

  • Soft Wood
  • Hard Wood
  • Glass & Metal
  • Fiberglass
  • Ceramics
  • Hard Plastics
  • Rubber
  • Laminating
  • Reinforcing

Works Good On:

  • Balsa Wood
  • Water-Resistant

 

Click to Download Safety Data Sheet

BSI-CA-135

$4.99

Bob Smith Industries Super-Gold+ Odorless Foam Safe CA (Medium)

Untitled Document

Description:

Bob Smith Industries CA Glue

Super-Gold+™ Odorless, CA

SUPER-GOLD™ and SUPER-GOLD+™ are our odorless INSTA-CURE CAs They are non-frosting and take only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes. The SUPER-GOLD™’s do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF’s. They will not fog clear plastic. SUPER-GOLD+™ is ideal for attaching clear canopies in plastic model kits; however, MAXI-CURE™ is still recommended for assembling the rest of plastic kits. Wood can be bonded to white foam with SUPER-GOLD +™ in less than fifteen seconds. For bonding foam to foam, spray a very light fog of INSTA-SET™ to one piece and apply SUPER-GOLD+™ to the other before joining. Excess INSTA-SET™ may create too much heat, which can melt the foam. Both SUPER-GOLD™’s cure to a more flexible consistency for better shock absorbtion. Whenever a large amount of CA is to be used in such applications as saturating fiberglass or Kevlar, SUPER-GOLD™ eliminates the irritating fumes from the evaporating monomer that make repeated use of CA unpleasant at times.

 

Works Best On:

  • Rubber
  • White Foam

Works Good On:

  • Balsa Wood
  • Soft Wood
  • Hard Wood
  • Glass & Metal
  • Fiberglass
  • Ceramics
  • Hard Plastics
  • Laminating
  • Water-Resistant
  • Reinforcing
  • CA Hinges

 

Avaliable in 2oz and 3/4 Pocket Size.

Pocket CAs feature a new top that has a pin built into the cap that covers the nozzle. This pin seals the bottle so that if it is tipped over, the bottle will not leak. This makes the Pocket CAs ideal for keeping in your tool or field box, just like our IC-Gel. One disadvantage that the new Pocket CA top has is the bluntness of the nozzle. This makes it more difficult to apply small amounts of the CA, especially in tight places. From the feedback we have received, it appears about 25-30% of users prefer the new Pocket CA top, which means that over 70% prefer our standard top for general bonding purposes. Most users are buying both types. Our original top for the workshop, and the Pocket CA for use out in the field. The 3/4 oz. Pocket CAs are available in BSI's Insta-Cure, Insta-Cure+, Maxi-Cure and Super-Gold+. BSI's new extender tip #304 works on the Pocket CA.

 

Click to Download Safety Data Sheet

BSI-CA-139

$12.99

Bob Smith Industries Foam-Cure

Untitled Document

Description:

Bob Smith Industries Foam Cure

Foam-Cure™

FOAM-CURE™ is a silicone based adhesive that works very well on EPP and EPO foams. It is crystal clear and cures to a more flexible consistency than CA. It is, however, not instant bonding like CA and there is no accelerator to speed it’s curing. To obtain a faster initial bond when bonding two pieces, FOAM-CURE™ can be applied to one piece and after the two are joined, they can then be pulled apart. After letting it air dry for about ten minutes, FOAM-CURE™ will act like a contact cement when the parts are rejoined, resulting in enough tack strength to allow the next steps of assembly. Full strength is reached in 10-12 hours.

FOAM-CURE™ works with all foams, and will actually bond most other materials. It will bond wood and plastic to foam, and is a good canopy glue. FOAM-CURE™ does not, however, cure flexible enough to act as a hinge for aircraft control surfaces. Its limitations occur when bonding large areas of two non-porous materials. FOAM-CURE™ requires exposure to air for drying. If one tried to bond, for example, a half-dollar coin to glass, over 90% of the adhesive would never cure, since the solvent it contains would have no where to evaporate. A small amount of denatured alcohol can be mixed into the Foam-Cure to make it thinner.

 

Works Best On:

  • EPP Foam
  • EOP Foam
  • Clear Canopy
  • Paper and Crafts

 

Cut off tip of nozzle. Apply to one part before joining. Use tape to hold parts in place during cure. For faster curing, pull the joint apart and let Foam-Cure™ air dry for 5-10 min before rejoining the parts. This results in enough tack strength to allow the next steps of assembly. Full cure takes 10-12 hours. Foam-Cure™ works on all foams, especially on EPP and EPO, and will bond a porous surface to non-porous materials. Foam-Cure™ is also an excellent glue for clear canopies, and will also bond paper. If needed, denatured alcohol can be used to thin or clean up uncured Foam-Cure™. Replace cap after use.

 

Click to Download Safety Data Sheet

 

BSI-FC-141

$2.99

Bob Smith Industries Insta-Set

Untitled Document

Description:

Bob Smith Industries Insta-Set

Insta-Set™

INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET™ can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET™ is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam.

 

Directions:

After joining parts with cyanoacrylate (CA, super glue), spray the seams with Insta-Set™ to cure the CA in 8 seconds. A bead of CA can then be applied to the outside and corners of joints before another application of Insta-Set™ to reinforce their strength. Insta-Set™ can also be applied to one part (with CA on the other) before joining for difficult to bond materials. Insta-Set™ is compatible with all surfaces, including clear plastic and all foams. It also is a great cleaning agent for adhesive residue and scuff marks. Store separately from CAs.

 

Works Best On:

 

Click to Download Safety Data Sheet

  • All Cyanoacrylates

BSI-AC-151

$5.99

Bob Smith Industries Super-Gold Odorless CA (Thin)

Untitled Document

Description:

Bob Smith Industries CA Glue

Super-Gold+™ Odorless, CA

SUPER-GOLD™ and SUPER-GOLD+™ are our odorless INSTA-CURE CAs They are non-frosting and take only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes. The SUPER-GOLD™’s do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF’s. They will not fog clear plastic. SUPER-GOLD+™ is ideal for attaching clear canopies in plastic model kits; however, MAXI-CURE™ is still recommended for assembling the rest of plastic kits. Wood can be bonded to white foam with SUPER-GOLD +™ in less than fifteen seconds. For bonding foam to foam, spray a very light fog of INSTA-SET™ to one piece and apply SUPER-GOLD+™ to the other before joining. Excess INSTA-SET™ may create too much heat, which can melt the foam. Both SUPER-GOLD™’s cure to a more flexible consistency for better shock absorbtion. Whenever a large amount of CA is to be used in such applications as saturating fiberglass or Kevlar, SUPER-GOLD™ eliminates the irritating fumes from the evaporating monomer that make repeated use of CA unpleasant at times.

 

Works Best On:

  • Rubber
  • White Foam

Works Good On:

  • Balsa Wood
  • Soft Wood
  • Hard Wood
  • Glass & Metal
  • Fiberglass
  • Ceramics
  • Hard Plastics
  • Laminating
  • Water-Resistant
  • Reinforcing
  • CA Hinges

 

Avaliable in 2oz and 3/4 Pocket Size.

Pocket CAs feature a new top that has a pin built into the cap that covers the nozzle. This pin seals the bottle so that if it is tipped over, the bottle will not leak. This makes the Pocket CAs ideal for keeping in your tool or field box, just like our IC-Gel. One disadvantage that the new Pocket CA top has is the bluntness of the nozzle. This makes it more difficult to apply small amounts of the CA, especially in tight places. From the feedback we have received, it appears about 25-30% of users prefer the new Pocket CA top, which means that over 70% prefer our standard top for general bonding purposes. Most users are buying both types. Our original top for the workshop, and the Pocket CA for use out in the field. The 3/4 oz. Pocket CAs are available in BSI's Insta-Cure, Insta-Cure+, Maxi-Cure and Super-Gold+. BSI's new extender tip #304 works on the Pocket CA.

 

Click to Download Safety Data Sheet

BSI-CA-122

$15.99

Bob Smith Industries 301 Extender Tips for CA Glue Bottles (6 Pack)

Bob Smith Industries 301 Extender Tips for CA Glue Bottles (6 Pack)

UN-CURE™ debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE™ will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water. Since cured CA is essentially acrylic plastic, anything that will dissolve CA will also soften most plastics. Care must be used, therefore, when using Un-Cure on plastics. Separating plastics parts with a razor saw is usually the best option. Un-Cure™ will soften cured super glue (aka cyanoacrylate, CA). To release bonded skin (not near the eyes) apply Un-Cure™, then use a small, rounded object like a paperclip to separate the skin with a peeling action, applying more Un-Cure™ as needed until the skin areas are debonded. Wash the area with soap and water. The natural shedding of the skin’s outer layer will remove any residual CA within 12 hr. For removing CA from hard surfaces, soak a cloth or paper towel in Un-Cure™ and rub areas vigorously. Un-Cure™, however, will mar most plastics.

 

Works Best On:

  • All Cyanoacrylates

 

Avaliable in 1 oz Size.

 

 

Click to Download Safety Data Sheet

BSI-301

$2.99

Bob Smith Industries Mid-Cure Epoxy (15 min)

Untitled Document

Description:

Bob Smith Industries CA Glue

Super-Gold+™ Odorless, CA

SUPER-GOLD™ and SUPER-GOLD+™ are our odorless INSTA-CURE CAs They are non-frosting and take only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes. The SUPER-GOLD™’s do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF’s. They will not fog clear plastic. SUPER-GOLD+™ is ideal for attaching clear canopies in plastic model kits; however, MAXI-CURE™ is still recommended for assembling the rest of plastic kits. Wood can be bonded to white foam with SUPER-GOLD +™ in less than fifteen seconds. For bonding foam to foam, spray a very light fog of INSTA-SET™ to one piece and apply SUPER-GOLD+™ to the other before joining. Excess INSTA-SET™ may create too much heat, which can melt the foam. Both SUPER-GOLD™’s cure to a more flexible consistency for better shock absorbtion. Whenever a large amount of CA is to be used in such applications as saturating fiberglass or Kevlar, SUPER-GOLD™ eliminates the irritating fumes from the evaporating monomer that make repeated use of CA unpleasant at times.

 

Works Best On:

  • Rubber
  • White Foam

Works Good On:

  • Balsa Wood
  • Soft Wood
  • Hard Wood
  • Glass & Metal
  • Fiberglass
  • Ceramics
  • Hard Plastics
  • Laminating
  • Water-Resistant
  • Reinforcing
  • CA Hinges

 

Avaliable in 2oz and 3/4 Pocket Size.

Pocket CAs feature a new top that has a pin built into the cap that covers the nozzle. This pin seals the bottle so that if it is tipped over, the bottle will not leak. This makes the Pocket CAs ideal for keeping in your tool or field box, just like our IC-Gel. One disadvantage that the new Pocket CA top has is the bluntness of the nozzle. This makes it more difficult to apply small amounts of the CA, especially in tight places. From the feedback we have received, it appears about 25-30% of users prefer the new Pocket CA top, which means that over 70% prefer our standard top for general bonding purposes. Most users are buying both types. Our original top for the workshop, and the Pocket CA for use out in the field. The 3/4 oz. Pocket CAs are available in BSI's Insta-Cure, Insta-Cure+, Maxi-Cure and Super-Gold+. BSI's new extender tip #304 works on the Pocket CA.

 

Click to Download Safety Data Sheet

BSI-PX-203

$11.99

Bob Smith Industries Slow-Cure Epoxy (30 min)

Untitled Document

Description:

Bob Smith Industries CA Glue

Super-Gold+™ Odorless, CA

SUPER-GOLD™ and SUPER-GOLD+™ are our odorless INSTA-CURE CAs They are non-frosting and take only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes. The SUPER-GOLD™’s do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF’s. They will not fog clear plastic. SUPER-GOLD+™ is ideal for attaching clear canopies in plastic model kits; however, MAXI-CURE™ is still recommended for assembling the rest of plastic kits. Wood can be bonded to white foam with SUPER-GOLD +™ in less than fifteen seconds. For bonding foam to foam, spray a very light fog of INSTA-SET™ to one piece and apply SUPER-GOLD+™ to the other before joining. Excess INSTA-SET™ may create too much heat, which can melt the foam. Both SUPER-GOLD™’s cure to a more flexible consistency for better shock absorbtion. Whenever a large amount of CA is to be used in such applications as saturating fiberglass or Kevlar, SUPER-GOLD™ eliminates the irritating fumes from the evaporating monomer that make repeated use of CA unpleasant at times.

 

Works Best On:

  • Rubber
  • White Foam

Works Good On:

  • Balsa Wood
  • Soft Wood
  • Hard Wood
  • Glass & Metal
  • Fiberglass
  • Ceramics
  • Hard Plastics
  • Laminating
  • Water-Resistant
  • Reinforcing
  • CA Hinges

 

Avaliable in 2oz and 3/4 Pocket Size.

Pocket CAs feature a new top that has a pin built into the cap that covers the nozzle. This pin seals the bottle so that if it is tipped over, the bottle will not leak. This makes the Pocket CAs ideal for keeping in your tool or field box, just like our IC-Gel. One disadvantage that the new Pocket CA top has is the bluntness of the nozzle. This makes it more difficult to apply small amounts of the CA, especially in tight places. From the feedback we have received, it appears about 25-30% of users prefer the new Pocket CA top, which means that over 70% prefer our standard top for general bonding purposes. Most users are buying both types. Our original top for the workshop, and the Pocket CA for use out in the field. The 3/4 oz. Pocket CAs are available in BSI's Insta-Cure, Insta-Cure+, Maxi-Cure and Super-Gold+. BSI's new extender tip #304 works on the Pocket CA.

 

Click to Download Safety Data Sheet

BSI-PX-205-

$11.99

Bob Smith Industries IC-LOC Blue Medium Strength Thread Locker

Untitled Document

Description:

Bob Smith Industries CA Glue

Super-Gold+™ Odorless, CA

SUPER-GOLD™ and SUPER-GOLD+™ are our odorless INSTA-CURE CAs They are non-frosting and take only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes. The SUPER-GOLD™’s do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF’s. They will not fog clear plastic. SUPER-GOLD+™ is ideal for attaching clear canopies in plastic model kits; however, MAXI-CURE™ is still recommended for assembling the rest of plastic kits. Wood can be bonded to white foam with SUPER-GOLD +™ in less than fifteen seconds. For bonding foam to foam, spray a very light fog of INSTA-SET™ to one piece and apply SUPER-GOLD+™ to the other before joining. Excess INSTA-SET™ may create too much heat, which can melt the foam. Both SUPER-GOLD™’s cure to a more flexible consistency for better shock absorbtion. Whenever a large amount of CA is to be used in such applications as saturating fiberglass or Kevlar, SUPER-GOLD™ eliminates the irritating fumes from the evaporating monomer that make repeated use of CA unpleasant at times.

 

Works Best On:

  • Rubber
  • White Foam

Works Good On:

  • Balsa Wood
  • Soft Wood
  • Hard Wood
  • Glass & Metal
  • Fiberglass
  • Ceramics
  • Hard Plastics
  • Laminating
  • Water-Resistant
  • Reinforcing
  • CA Hinges

 

Avaliable in 2oz and 3/4 Pocket Size.

Pocket CAs feature a new top that has a pin built into the cap that covers the nozzle. This pin seals the bottle so that if it is tipped over, the bottle will not leak. This makes the Pocket CAs ideal for keeping in your tool or field box, just like our IC-Gel. One disadvantage that the new Pocket CA top has is the bluntness of the nozzle. This makes it more difficult to apply small amounts of the CA, especially in tight places. From the feedback we have received, it appears about 25-30% of users prefer the new Pocket CA top, which means that over 70% prefer our standard top for general bonding purposes. Most users are buying both types. Our original top for the workshop, and the Pocket CA for use out in the field. The 3/4 oz. Pocket CAs are available in BSI's Insta-Cure, Insta-Cure+, Maxi-Cure and Super-Gold+. BSI's new extender tip #304 works on the Pocket CA.

 

Click to Download Safety Data Sheet

BSI-IC-171

$5.99