Miracle Fuel Tank Cap with switch valve

Introducing the Red Miracle Brushless Motor Smoke Pump! These light weight pumps have a CNC processed 6061 case with a Japanese high speed oil seal. The brushless motor/ESC supply smooth transmission and helps avoid the possibility of a spark.

Basic Set up:

First connect the pump to the ESC, fuel filters, muffler and smoke tank (drawing included to help with this).Plug your radio connector into the switched channel (such as landing gear or flaps). Turn on radio, make sure switch is off (100% negative) for at least 5 seconds and turn on. If the pump pushes fluid toward the muffler, the set up is correct. If it tries to pump toward the tank, please change any two wires' connection of the three wires connect the brushless motor and ESC.

Radio Set up:

3. Non programmable Radios

Use a switched channel to switch the Smoke pump on and off. Since there is no trim control on a switched channel, the flow rate is consistent. When the switch is on, flow will be at maximum. We can set the END POINT/ATV of radio switch channel to control the maximum flow rate so as to control the smoke density.

4. Programmable Radios

Plug the smoke signal wire into a spare channel (such as the 8th channel). Set this channel program mixing the Throttle channel, then set a switch for programming mixing on/off to control smoke pump on/off. Adjust the END POINT/Travel of this channel to control smoke pump flow rate so as to control the smoke density. For more detailed information please see your radio manual.

Specifications:

• Weight: 3.32 oz (94g)
• 1100KV Brushless Motor
• 10 Amp Brushless ESC
• Input: 2-cell lipo or Li-FE (6-cell NiMH)
• CNC processed 6061 anodized aluminum
• Fuel resistant fiberglass filled nylon gears
   

  **DO NOT dry run pump! This may cause failure and will void warranty.**

   

Retractable Gasoline Fuel Tube and 1M Fuel Line

Specifications:

• High Quality Carbon Fiber Spinners
• Pre Slotted for 3d size props
• Strong
• Lightweight
• Beautiful!

Pricing:

• 2.0" $19.99 *new size
• 2.5" $24.99 *new size
• 3.0" $34.99
• 3.5" $39.99
• 3.75" $44.99 *new size
• 4.0" $49.99
• 4.5" 59.99
• 5.0" 65.99

**NOTE: Spinner Bolts sold SEPARATELY - CLICK HERE -

Carbon Fiber Wing Tube with Fiberglass Sleeve Matched Set

RedwingRC Carbon Fiber Wing Tubes are strong and light weight, exactly the way it should be. They provide your wings with a lot of strength so you can fly till your heart's content without adding any extra weight.

Available in three sizes, a 20cc, 30cc and 50cc size.

Details (approx.):

20cc - Diameter: 3/4" / Length: 24 1/4"
30cc - Diameter: 3/4" / Length: 29 5/8"
50cc - Diameter: 1" / Length: 38 3/8"


 

GPS Speed Meter (Speedometer for Flying or Track)

WHEEL AXLES FOR 30CC/50CC AIRPLANE - SET (2 PCS)

• Yak carbon fiber replacement gear Sbach carbon fiber replacement gear MXSR/MX2 carbon fiber replacement gear Extra carbon fiber replacement gear Edge carbon fiber replacement gear etc
  
  A - Sbach, MXSR, Slick, Edge, Extra 260
  B - Yak, Sukoi
  C - Yak also
  PLEASE NOTE: THE GEAR HAVE NOT BEEN DRILLED SO YOU CAN MATCH IT TO YOUR PLANE.

Dimensions (match the below information to the inset photo)

• 30cc A STYLE (3.6 oz)
  • A=6.5"
  • B=16.75"
  • C=6.25"
  • D=1.375" taper to 1"
  • E=1"

• 30cc B STYLE (3.8 oz)
  • A=7.5"
  • B=16"
  • C=5.5"
  • D=1.187" taper to 1"
  • E=1.5"

• 30cc C STYLE (3.4 oz)
  • A=6.5"
  • B=15.5"
  • C=5.5"
  • D=1.125" taper to .75
  • E=1"

• 50cc A STYLE (8.2 oz)
  • A=9.25"
  • B=18.75"
  • C=8"
  • D=1.5" taper to 1.125"
  • E=1.5"

• 50cc B STYLE (6 oz)
  • A=8.75"
  • B=18.5"
  • C=6.5"
  • D=1.5" taper to 1"
  • E=1.25"

• 50cc C STYLE (6 oz)
  • A=7.75"
  • B=18.5"
  • C=6.25"
  • D=1.5" taper to 1"
  • E=1.0"

Redwing RC Logo Stickers (6"- 48")

Want to show your RedwingRC spirit?

Check out these awesome vinyl graphics for your car, truck, wall of your trailer, they work and look great anywhere! These high quality graphics are printed on quality air release vinyl for easy bubble free applications and are contour cut with color bleeds(where applicable) to prevent any stray white spots on the edges of the vinyl. Redwing graphics are laminated for MAXIMUM longevity so they will look great year round.

Key Features of laminated graphics:

• Decreases fading and scratching
• Has a nice glossy sheen
• Increases vinyl life
• Easy cleaning


• Available in 9", 12”, 18”, 24”, 36”,and 48”

ProLine Male to Male Heavy Duty Servo Cables (20Awg for HV)

Booma RC pin flag switch for IntelliReg, Smart-Fly or Gryphon regulator. This pin flag switch Booma RC is an ultra high quality fail safe switch designed as a replacement switch for Smart-Fly systems, Power System, Power Expander, Regulators as well as Gryphon Heli regulators.

Supplied with 1 x switch actuator and 1 x pin flags.

Weighted Felt Fuel Clunk

Fuel clunks are a must for aerobatic flying. It insures that fuel is always flowing to the engine because the fuel line will follow gravity inside your tank. Without one, you increase the chance that your plane may stall when flying inverted or performing different maneuvers. Installing a fuel clunk is simple to install and an investment that any serious pilot should make.

13x16mm

.4 oz

Weighted Fuel Clunk

Fuel clunks are a must for aerobatic flying. It insures that fuel is always flowing to the engine because the fuel line will follow gravity inside your tank. Without one, you increase the chance that your plane may stall when flying inverted or performing different maneuvers. Installing a fuel clunk is simple to install and an investment that any serious pilot should make.

13x16mm

.4 oz

Standoff (25mm) 50-70CC (Anodized Gas Engine 25mm Stand Off Mounting Kit w/5mm Nuts & Bolts- 4pcs)

High Quality 1" Aluminum servo arm from Spot-On RC

Spot On Servo Arms are made of high quality 7075-T6 aluminum, one of the highest strength alloys available for this purpose.  They feature an ultra secure double lock design, keeping your servo arm secure and eliminating any slop between the main servo gear and the arm.  Spot On Servo Arms are also sand blasted and anodized for a beautiful appearance.

Spot on offers their servo arms in many sizes, threads and gear output compatibility.  Spot On arms are offered in:
M3, or #4-40 holes, so you can use ball links that are metric or standard Futaba, Hitec or JR compatible gear mesh. Sizes ranging from 1” to 2” for single arms and 2.5” to 4.5” for rudder arms.

Available colors are Black or Silver

Spot On RC Servo Arms are measured from the center hole of the servo to the outermost hole (for example, a 1” arm is exactly 1” from hole center to hole center).  However the larger sizes offer the option of one or two more additional inner holes so you can use them for future projects or fine tune your ratios.

Redwing RC only offers the V2, upgraded version, with stronger aluminum and finer design.  No matter which Spot On RC Servo Arms you choose you will be sure to experience problem free set up and operation with these high quality servo arms.
 

Standoff (17-20mm) 50-70CC (Anodized Gas Engine 25mm Stand Off Mounting Kit w/5mm Nuts & Bolts- 4pcs)

High Quality 1" Aluminum servo arm from Spot-On RC

Spot On Servo Arms are made of high quality 7075-T6 aluminum, one of the highest strength alloys available for this purpose.  They feature an ultra secure double lock design, keeping your servo arm secure and eliminating any slop between the main servo gear and the arm.  Spot On Servo Arms are also sand blasted and anodized for a beautiful appearance.

Spot on offers their servo arms in many sizes, threads and gear output compatibility.  Spot On arms are offered in:
M3, or #4-40 holes, so you can use ball links that are metric or standard Futaba, Hitec or JR compatible gear mesh. Sizes ranging from 1” to 2” for single arms and 2.5” to 4.5” for rudder arms.

Available colors are Black or Silver

Spot On RC Servo Arms are measured from the center hole of the servo to the outermost hole (for example, a 1” arm is exactly 1” from hole center to hole center).  However the larger sizes offer the option of one or two more additional inner holes so you can use them for future projects or fine tune your ratios.

Redwing RC only offers the V2, upgraded version, with stronger aluminum and finer design.  No matter which Spot On RC Servo Arms you choose you will be sure to experience problem free set up and operation with these high quality servo arms.