TOPRC SPARK-3 RTF 65mm 6-axis Gyro 5.8G FPV 800TVL Camera With Altitude Hold Headless Mode RC Drone Quadcopter

Power HD RX30 Receiver Voltage Stabilizer

Description:

Thought our other servos were great? Well of course they are! But wait until you check out these new Power HD servos - they will rock your wheel pants off* (no wheel pants will be harmed by using this product - but you get the idea).

There's a storm brewing in Redwing RC! These new HD Storms can handle anything thrown at them. Now, we can't imagine your servos heading into battle facing a hurricane or tornado - but they sure behave as if they have fought and conquered the fiercest of storms - taking all of that power and knowledge with them when they are installed into your bird. Rain or shine, these servos are ready for anything!

The HD Storm 3s are high efficiency and perform better. They run cooler and quieter and with less vibration - because there are no brush arcings, the radio frequency interference and electronic noise is significantly reduced.

All aluminum housing, high voltage and the new brushless technology gives you the best strength and speed while being incredibly efficient and long lasting.

New and Improved Technology!

The Power HD Storm 3 high voltage servos are made with brushless technology. Now - we've heard about this "brushless" stuff before but it is time to ask the question on all of our minds - why is that so great? Take a brushless motor for example - no brushes in a brushless motor (no kidding...) nor does it have the commutator - instead a small circuit board coordinates the energy delivery to the windings. Think about this technology being used in a power tool - since the electronics communicate directly with the stationary windings the tool can adapt to its surroundings - only using enough juice necessary to accomplish the job. So if you are using a brushless drill to drive a screw into Styrofoam - it will sense the lack of resistance from the foam and pulls only enough charge from the battery that it needs. Whereas a brushed drill will run as fast and hard as it can no matter the job simultaneously wasting your battery life.

"What the heck does that have to do with my servo?" Well now they are incorporating that smart technology into these HD Storm 3 high voltage servos - so they are not going to be sucking the life of your Redwing LiFe battery when it doesn't have to - which means not only would you be getting a great and powerful servo - it's smart! Your "LiFe" will thank you.

So now the only question is - why are you still reading this? Go buy your Power HD Storm 3 servos before they're gone!

Specs:

• Torque:
  • 374.9 oz/in at 6V (27.0 kg/cm)
  • 444.4 oz/in at 7.4V (32.0 kg/cm)
     
• Speed:
  • .14 sec at 6VV
  • .11 sec at 7.4V
     
• Voltage: 6.0 ~ 8.4 V
• Weight: 2.82 oz (80g)
• Size: 1.57 x 0.79 x 1.53 in (40.0 x 20.0 x 38.0mm)
   
• Operating Temp- -20~60centigrade
• Working Frequency - 1520μs / 333hz
• BRUSHLESS Motor
• Double Ball Bearings
• Titanium and Steel gears
• Water resistant O-Rings

Lemon RX DSMP (DSMX/DSM2 COMPATIBLE) MICROBRICK WITH 2 ON-BOARD SERVOS and MOLEX 1.25MM CONNECTOR PACKAGE 

Description:

Lemon Rx DSMX Compatible 6-Channel Receiver + Lemon DSMX Compatible Satellite

Highlight
- FailSafe for all channels via press of a button
- DSMX Satellite port

Understanding the receiver

Setup Instruction

Binding

1. Plug bind plug to the receiver.
2. Provide power to the unit. LED flashes quickly.
3. Enable bind mode in transmitter and ensure distance separation of 2 meters from receiver. Solid LED light means binding is completed.
4. Remove bind plug.

Setting Failsafe

1. Start by binding the receiver to the transmitter in the normal way and proceed as follows to set failsafe
2. Ensure that transmitter and receiver are turned on.
3. Insert bind plug into the receiver (Note: to set failsafe, bind plug is applied only when the receiver is turned on).
4. Set transmitter controls to the desired failsafe positions.
5. Press the side pushbutton to memorize failsafe settings.
6. Observe that the green light at the end of the receiver turns on to indicate failsafe is set. (Repeat step 4 will cause the LED to turn off which means failsafe is disabled).
7. Remove bind plug.
8. Disconnect the power for at least 2 seconds and then reconnect the power again. Test failsafe by turning off the transmitter.