2-in-1 15A UBEC and Digital Display Switch

Description:
The HS-5645MG is one of the best choices you can make for a 50cc sized plane for the cost. They will also work well in 30cc planes. It is fully programmable using Hi Tec's programmer. The combination of torque, speed, price and extreme holding power make it a favorite among pilots. Special alloy gears called “Alumite” offer tremendous strength yet are lightweight as well.


Specifications:

• Torque:
  • 143 oz/in at 4.8V (10.3 kg/cm)
  • 168 oz/in at 6V (12.1 kg/cm)
     
• Speed:
  • .23 sec at 4.8V
  • .18 sec at 6V
     
• Voltage: 4.8V - 6V
• Weight: 2.11oz (59.82g)
• Size: 40.6 x 19.8 x 37.8mm (1.59 x 0.77 x 1.48in)
   
• Motor Type: 3 Pole Ferrite
• Bearing Type: Dual Ball Bearing
• Gear Type: 3 Metal Gears and 1 Resin Metal Gear
• Connector Wire Length: 11.81" (300mm)
• Control System: +Pulse Width Control 1500usec Neutral
• Required Pulse: 3-5 Volt Peak to Peak Square Wave
• Operating Temperature Range: -20 to +60 Degree C
• Operating Angle: 45 Deg. one side pulse traveling 400usec
• 360 Modifiable: Yes
• Direction: Clockwise/Pulse Traveling 1500 to 1900usec
• Dead Band Width: 8usec
• Potentiometer Drive: Indirect Drive
• Current Drain (4.8V): 8.8mA/idle and 400mA no load operating
• Current Drain (6.0V): 9.1mA/idle and 500mA no load operating

Description:
These Miracle fuel dots are GREAT looking and function just as well. They are made of machined aluminum, and have a neoprene O-ring for a tight fuel proof fit. They include all the hardware you need and work with all standard size tygon tubing.

TEMPORARILY BACK ORDERED. Add to cart to PRE ORDER and we will ship ASAP. Email us for updated estimated ship date.

Booma RC Regulatori-Switch (6 V Regulated Dual Battery Redundancy switch with Fail-Safe Tech) 

If you want a switch that offers complete dual battery balancing and redundancy with an ultra-small footprint for your scale model then look no further. The new Booma RC intelligent redundant battery balancing switch is the answer.

This switch works with any single or dual battery system. Works with battery chemistry and voltage range from 2.5v to 28v. It comes with a Pin Flag and Ultra Bright Blue LED which can be mounted discretely on your scale model. The Pin Flag controls the internally mounted switch and battery redundancy circuit. The result - beautiful scale appearance with dual battery redundancy peace of mind.

This new balancing technology offers zero voltage drop battery balancing and redundancy which means it can handle huge loads without generating heat. This also means your receiver and servos get all the power unlike conventional battery balancing which loses precious power as heat.

Package Includes:

• 1 x Pin Flag Switch with mounting hardware.

• 1 x Ultra Bright Blue LED with mounting hardware.

• 1 x Dual Battery Balancing power switch circuit.

• 2 x sets of Input and Output JR connectors.

 

 

Specs:

 

 

• Ultra low foot print for the best scale looks.

• Works with single or dual battery configuration.

• Works with all battery chemistries. LiFe. LiPo, Lion, NiMh, NiCD. Battery voltage range can be from 2.5volts to 28 volts.

• Capable of handling input voltages up to 28volts.

•  Minimal external footprint - All you see on the outside of your model is a 3mm Pin Flag socket and (if required) an ultra-high bright Blue LED. The Pin Flag controls the internal power switch and dual battery redundancy.

• Full Dual Battery Redundancy - If one battery fails the other battery takes full control.

•  Maximum Battery Power Balancing - In a dual battery system HS1 draws current proportionally from both batteries while moving both batteries to a complete load balance situation. This means you get the maximum capacity out of both batteries all the time.

• 2 x 25 amp independent circuits. HS1 is 2 x 25amp circuits into a high power matching battery redundancy circuit. HS1 actually uses 4 x 50 amp rated FET circuits for battery power matching. We passively rate HS1 at 25amps per circuit.