Booma RC Wallaby Switch with Active Dual Battery Redundancy and Voltage Monitoring

Description:
The Optical Kill Switch for gas rc planes, allows you to safely and remotely kill your electronic ignition. It is Fiber Optically Coupled to isolate your ignition system from your radio system so there is NO interference



Features:

• Includes a remote mountable bright LED to indicate when the ignition is armed.
• Fiber Optic coupled input/output.
• Li-Po/Li-lon/A123/Ni-Mh/NiCad Input.
• Up to 20 Volt 16 amp MOS-FET(IRF7456) output.
• Low to 3Volt 3amp output.
• Low Voltage Drop-Less than 150mv.
• 100% Surface Mount Technology.
• Heavy Gauge Wires,universal connectors.
• Small and light weight –only 0.3 OZ!(8g)
• Reverse Bettery input protection.
• Shut down the transmitter power or receiver to cut off automatically when kill engine




 
•  

SCORPION A-5524-205kv Motor for Giant Scale Airplane (12S 35-40cc)

Overview

The Tomcat G30cc Motor For 30cc gas airplane This is a high-end motor combines ultra-high power and super efficient design to deliver outstanding performance.

Specifications

• Type:......................... TC-G-6432-KV200(G30CC)
• KV(rpms per volt):... 200
• No load current: ....... 2.2 A @10V
• Resistance:................ 0.04 ohms
• Watts:........................ up to 3000
• Continuous Current:... 65A
• Max Burst Current:.... 80A,10seconds
• Cells:......................... 10 S Li-Po
• Recommended Props: 20x12 to 22x11
• Slots,Poles:............... 24,20
• Diameter:.................. 64 mm
• Shaft: Diameter:........ 10 mm
• Weight:...................... 680 g
• Brushless ESC:......... 100A

Push Button Switch Actuator with LED

If you want a switch that offers complete dual battery balancing and redundancy with an ultra-small footprint for your scale model then look no further. The new Booma RC intelligent redundant battery balancing switch is the answer.

This switch works with any single or dual battery system. Works with battery chemistry and voltage range from 2.5v to 28v. It comes with a Pin Flag and Ultra Bright Blue LED which can be mounted discretely on your scale model. The Pin Flag controls the internally mounted switch and battery redundancy circuit. The result - beautiful scale appearance with dual battery redundancy peace of mind.

This new balancing technology offers zero voltage drop battery balancing and redundancy which means it can handle huge loads without generating heat. This also means your receiver and servos get all the power unlike conventional battery balancing which loses precious power as heat.

Package Includes:

• 1 x Pin Flag Switch with mounting hardware.

• 1 x Ultra Bright Blue LED with mounting hardware.

• 1 x Dual Battery Balancing power switch circuit.

• 2 x sets of Input and Output JR connectors.

Specs:

• Ultra low foot print for the best scale looks.

• Works with single or dual battery configuration.

• Works with all battery chemistries. LiFe. LiPo, Lion, NiMh, NiCD. Battery voltage range can be from 2.5volts to 28 volts.

• Capable of handling input voltages up to 28volts.

•  Minimal external footprint - All you see on the outside of your model is a 3mm Pin Flag socket and (if required) an ultra-high bright Blue LED. The Pin Flag controls the internal power switch and dual battery redundancy.

• Full Dual Battery Redundancy - If one battery fails the other battery takes full control.

•  Maximum Battery Power Balancing - In a dual battery system HS1 draws current proportionally from both batteries while moving both batteries to a complete load balance situation. This means you get the maximum capacity out of both batteries all the time.

• 2 x 25 amp independent circuits. HS1 is 2 x 25amp circuits into a high power matching battery redundancy circuit. HS1 actually uses 4 x 50 amp rated FET circuits for battery power matching. We passively rate HS1 at 25amps per circuit.