Products Map - RedwingRC.com

TEMPORARILY BACK ORDERED. Add to cart to PRE ORDER and we will ship ASAP. Email us for updated estimated ship date.

Booma RC Regulatori-Switch (6 V Regulated Dual Battery Redundancy switch with Fail-Safe Tech) 

If you want a switch that offers complete dual battery balancing and redundancy with an ultra-small footprint for your scale model then look no further. The new Booma RC intelligent redundant battery balancing switch is the answer.

This switch works with any single or dual battery system. Works with battery chemistry and voltage range from 2.5v to 28v. It comes with a Pin Flag and Ultra Bright Blue LED which can be mounted discretely on your scale model. The Pin Flag controls the internally mounted switch and battery redundancy circuit. The result - beautiful scale appearance with dual battery redundancy peace of mind.

This new balancing technology offers zero voltage drop battery balancing and redundancy which means it can handle huge loads without generating heat. This also means your receiver and servos get all the power unlike conventional battery balancing which loses precious power as heat.

Package Includes:

• 1 x Pin Flag Switch with mounting hardware.

• 1 x Ultra Bright Blue LED with mounting hardware.

• 1 x Dual Battery Balancing power switch circuit.

• 2 x sets of Input and Output JR connectors.

Specs:

• Ultra low foot print for the best scale looks.

• Works with single or dual battery configuration.

• Works with all battery chemistries. LiFe. LiPo, Lion, NiMh, NiCD. Battery voltage range can be from 2.5volts to 28 volts.

• Capable of handling input voltages up to 28volts.

•  Minimal external footprint - All you see on the outside of your model is a 3mm Pin Flag socket and (if required) an ultra-high bright Blue LED. The Pin Flag controls the internal power switch and dual battery redundancy.

• Full Dual Battery Redundancy - If one battery fails the other battery takes full control.

•  Maximum Battery Power Balancing - In a dual battery system HS1 draws current proportionally from both batteries while moving both batteries to a complete load balance situation. This means you get the maximum capacity out of both batteries all the time.

• 2 x 25 amp independent circuits. HS1 is 2 x 25amp circuits into a high power matching battery redundancy circuit. HS1 actually uses 4 x 50 amp rated FET circuits for battery power matching. We passively rate HS1 at 25amps per circuit.

Replacement canopy for the 50cc Sbach 342 Yellow Thunder Bolt Scheme.

Replacement Cowl 58" Extra 330 (70e) 

Replacement Cowl and Canopy for 50cc V1 Extra 330 (Red, Silver, Black Scheme)
Canopy Dimensions:  Forward Edge 11 3/8, Aft Edge 7 1/8 Length 29 1/8 Forward Height 1 3/4 Aft Height 5 3/8

Cylinder for PTE 36cc.(25)

Replacement Left wing for the 50cc Sbach 324 Yellow Thunder Bolt Scheme.

Replacement Rubber Cap and Aluminum Starter Cone for 20-80cc ESTDB Electric Starter

Replacementr Rubber Cap and Aluminum Starter Cone for 80-250cc ESTDT Electric Starter

Replacement Rudder for the 50cc Slick (Green & White Scheme)

Replacement Wings for the 50cc 2016 V3 Extra 330 Blue. This set of wings includes the wing tube. Although this is a set of two wings (Left & Right), please contact us if you are in need of a single wing.

This set includes L & R Wings, Wings tube, and SFGs

Replacement wings for the 50cc Slick 540 Green & White Scheme. This set of wings includes the wing tube. Although this is a set of two wings (Left & Right), please contact us if you are in need of a single wing.

Replacement Wings for V2 50cc Extra 330 (Red, Silver Scheme) This is a set of 2 wings (left & Right) will need to be re-covered to match your scheme. Please contact us if you are in need of a single 50cc size wing.

Includes Silver Side Force Generators