Professional Model Airplane X Display Stand/Holder

Description:
The HS-5645MG is one of the best choices you can make for a 50cc sized plane for the cost. They will also work well in 30cc planes. It is fully programmable using Hi Tec's programmer. The combination of torque, speed, price and extreme holding power make it a favorite among pilots. Special alloy gears called “Alumite” offer tremendous strength yet are lightweight as well.


Specifications:

• Torque:
  • 143 oz/in at 4.8V (10.3 kg/cm)
  • 168 oz/in at 6V (12.1 kg/cm)
     
• Speed:
  • .23 sec at 4.8V
  • .18 sec at 6V
     
• Voltage: 4.8V - 6V
• Weight: 2.11oz (59.82g)
• Size: 40.6 x 19.8 x 37.8mm (1.59 x 0.77 x 1.48in)
   
• Motor Type: 3 Pole Ferrite
• Bearing Type: Dual Ball Bearing
• Gear Type: 3 Metal Gears and 1 Resin Metal Gear
• Connector Wire Length: 11.81" (300mm)
• Control System: +Pulse Width Control 1500usec Neutral
• Required Pulse: 3-5 Volt Peak to Peak Square Wave
• Operating Temperature Range: -20 to +60 Degree C
• Operating Angle: 45 Deg. one side pulse traveling 400usec
• 360 Modifiable: Yes
• Direction: Clockwise/Pulse Traveling 1500 to 1900usec
• Dead Band Width: 8usec
• Potentiometer Drive: Indirect Drive
• Current Drain (4.8V): 8.8mA/idle and 400mA no load operating
• Current Drain (6.0V): 9.1mA/idle and 500mA no load operating

Description:

All NEW design! These Miracle aluminum spinners have back plates which have extensive lightening, the spinners are cut for a large 3d style prop, and the back plates are drilled for multiple engine sizes!

FOR ENGINE SIZE:

• 2.5" Spinner : DLE 20, Enya FS120, All YS Four Strokes and any that match these
• 2.5" Spinner : DLE 20, Enya FS120, All YS Four Strokes and any that match these
• 3" Spinner: DLE 30, DLE 35RA, DLE 55, DLE 55RA, MLD 28, DA 50, 56, 58, and EVO 54 (and any other engines that fit these templates
• 3.5" DLE 30, DLE 35RA, DLE 55, DLE 55RA, MLD 28, DA 50, 56, 58, and EVO 54 (and any other engines that fit these templates
  
  SPECS:
• 2.5": Height 2.7", weight 2.7oz, includes 30mm bolt.
• 3": Height - 3.1", weight 3.2 oz, includes 55mm bolt.
• 3.5" : Height 3.7", weight 3.6oz, includes 60mm bolt.

Miracle RC Aluminum Spinners are high quality CNC Machined spinners. Very light, with a lightened back plate included. Very accurate, very beautiful, and a great value!

• 2.5" - $16.95
• 3" - $20.95
• 3.5" - $27.95
• 3.75"- $31.95
• 4.0" - $38.95
• 4.5" - $44.95
• 5" - $50.95

Description:
This Miracle RC Fuel pump is a MUST have accessory. Saves you time and elbow grease when filling up your tank. The case is CNC process 6061, and it has a hardened pump barrel. It has a magnet on the outside, so you it can stick right onto metal containers!

The gears are fuel proof nylon, and fiberglass filled
The gear shaft is stainless steel
Japaneese oil seals
The end-seal O-ring is made of butadience-acrylonitrile rubber - so it can be used with nitro, gas, or even kerosene
volatage: 7.2 to 12V
Flow rate: 1000ml/min at 11.1V
Includes a filtered nozzle and clunk

DO NOT DRY RUN