RedwingRC Accessories

Tariff Information update

more offers

HiTec DB777WP 32bit Brushless Low Profile Waterproof Full Metal Case (IP-67 Rated) 11kg/153oz [email protected]

Ask a question about this product

Printable version

Options

Market Price: $199.99

Our Price:

$134.99

You Save

33%

Quantity (15)

Details


Availability	15 in stock
Weight	0.38 lbs
SKU	HRC36778S
Manufacturer	Hitec

RWRC is excited to introduce the new addition to the Hitec D-Series servo line, the high-performance, low profile DB777WP. Designed with a full metal, IP-67 rated waterproof case, this advanced, programmable servo is our fastest, low profile option for 1/10 buggy and touring car drivers. The DB777WP is powered by our 32-bit MCU (Microcontroller Unit) and 12-bit ADC (Analog to Digital Converter), bringing high resolution, rapid response, and patented Smart Sense technology to kick your ride into top gear! Look to us when you need unprecedented engineering, and the ultimate reliability!

FEATURES

Voltage Range is 4.8V - 8.4V
Full Programmability
IP-67 Waterproof Rated
Ultra Efficient Brushless Motor
32-Bit MCU Technology / 4096 Resolution
Smart Sense Technology for Servo Analytics
High Response, High Resolution Circuitry
Full Metal Case
1M Cycle, Long-Life Potentionmeter
H25T -Industry Standard Output Spline
Compatible with Fully Charged 2S LiPo Batteries

D777WP SERVO SPECIFICATIONS

Performance Specifications
Operating Voltage Range (Volts DC)	6.0V ~ 7.4V
Speed (Second @ 60°)	0.08 ~ 0.06
Maximum Torque Range oz. / in.	111 ~ 153
Maximum Torque Range kg. / cm.	8.0 ~ 11.0
Current Draw at Idle	35mA / 40mA
No Load Operating Current Draw	250mA / 350mA
Stall Current Draw	3500mA / 4500mA
Dead Band Width	1usec
Physical Specifications
Dimensions (Inches)	1.61 x 0.83 x 1.04 in.
Dimensions (Metric)	41.0 x 21.0 x 26.5
Weight (Ounces)	2.40
Weight (Gram)	68.0
Circuit Type	32bit Programable Digital
Motor Type	Brushless
Gear Material	Metal
Bearing Type	Brushless
Output Shaft (type / Ømm)	H25T
Case Material	Aluminum
Dust / Water Resistance	IP-67 Rated
Connector Gauge (AWG) / Strand Count	20AWG / 80
Radio Control Applications
Parkflyer	N / A
Sport Plane	N / A
Sailplane	N / A
3D Performance	N / A
Scale	N / A
Electric Helicopter	N/A
Gas Helicopter	N/A
On Road	1/8th
Monster Truck	N/A
Buggies	1/8th
Truggies	N/A
Short Course / Truck	N/A
Crawlers	N / A
Sail Boat	N / A
Power Boat	N / A

Bob Smith Industries 301 Extender Tips for CA Glue Bottles (6 Pack)

UN-CURE™ debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE™ will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water. Since cured CA is essentially acrylic plastic, anything that will dissolve CA will also soften most plastics. Care must be used, therefore, when using Un-Cure on plastics. Separating plastics parts with a razor saw is usually the best option. Un-Cure™ will soften cured super glue (aka cyanoacrylate, CA). To release bonded skin (not near the eyes) apply Un-Cure™, then use a small, rounded object like a paperclip to separate the skin with a peeling action, applying more Un-Cure™ as needed until the skin areas are debonded. Wash the area with soap and water. The natural shedding of the skin’s outer layer will remove any residual CA within 12 hr. For removing CA from hard surfaces, soak a cloth or paper towel in Un-Cure™ and rub areas vigorously. Un-Cure™, however, will mar most plastics.