Newton 358mm Micro Indoor Laser-Cut Balsa Wood Model (Kit, PNP or BNF Electric Power version)
Newton 358mm Micro Indoor Laser-Cut Balsa Wood Model (Kit, PNP or BNF Electric Power version) Our model captures the very essence of this homebuilt aircraft. This Micro Balsa plane is built from balsa and hardwoods with all the parts beautifully laser cut that are extremely accurate allowing you to build the perfect model. The PNP kit is easy to operate and suitable for beginners and comes with everything you need except your battery and RX/TX. The BNF version includes 2 batteries and charger plus a DSMX/2 Receiver. Specification:
Optional Power System:
Kit Versions:
|
Bob Smith Industries Foam-Cure
| Untitled Document Description:Bob Smith Industries Foam Cure Foam-Cure™FOAM-CURE™ is a silicone based adhesive that works very well on EPP and EPO foams. It is crystal clear and cures to a more flexible consistency than CA. It is, however, not instant bonding like CA and there is no accelerator to speed it’s curing. To obtain a faster initial bond when bonding two pieces, FOAM-CURE™ can be applied to one piece and after the two are joined, they can then be pulled apart. After letting it air dry for about ten minutes, FOAM-CURE™ will act like a contact cement when the parts are rejoined, resulting in enough tack strength to allow the next steps of assembly. Full strength is reached in 10-12 hours. FOAM-CURE™ works with all foams, and will actually bond most other materials. It will bond wood and plastic to foam, and is a good canopy glue. FOAM-CURE™ does not, however, cure flexible enough to act as a hinge for aircraft control surfaces. Its limitations occur when bonding large areas of two non-porous materials. FOAM-CURE™ requires exposure to air for drying. If one tried to bond, for example, a half-dollar coin to glass, over 90% of the adhesive would never cure, since the solvent it contains would have no where to evaporate. A small amount of denatured alcohol can be mixed into the Foam-Cure to make it thinner.
Works Best On:
Cut off tip of nozzle. Apply to one part before joining. Use tape to hold parts in place during cure. For faster curing, pull the joint apart and let Foam-Cure™ air dry for 5-10 min before rejoining the parts. This results in enough tack strength to allow the next steps of assembly. Full cure takes 10-12 hours. Foam-Cure™ works on all foams, especially on EPP and EPO, and will bond a porous surface to non-porous materials. Foam-Cure™ is also an excellent glue for clear canopies, and will also bond paper. If needed, denatured alcohol can be used to thin or clean up uncured Foam-Cure™. Replace cap after use.
Click to Download Safety Data Sheet
|
BSI-AC
$2.99
Miracle Brushless Smoke Pump
| New Miracle Brushless Smoke Pump
Description:Introducing the Red Miracle Brushless Motor Smoke Pump! These light weight pumps have a CNC processed 6061 case with a Japanese high speed oil seal. The brushless motor/ESC supply smooth transmission and helps avoid the possibility of a spark. Basic Set up:First connect the pump to the ESC, fuel filters, muffler and smoke tank (drawing included to help with this).Plug your radio connector into the switched channel (such as landing gear or flaps). Turn on radio, make sure switch is off (100% negative) for at least 5 seconds and turn on. If the pump pushes fluid toward the muffler, the set up is correct. If it tries to pump toward the tank, please change any two wires' connection of the three wires connect the brushless motor and ESC. Radio Set up:3. Non programmable Radios Use a switched channel to switch the Smoke pump on and off. Since there is no trim control on a switched channel, the flow rate is consistent. When the switch is on, flow will be at maximum. We can set the END POINT/ATV of radio switch channel to control the maximum flow rate so as to control the smoke density. 4. Programmable Radios Plug the smoke signal wire into a spare channel (such as the 8th channel). Set this channel program mixing the Throttle channel, then set a switch for programming mixing on/off to control smoke pump on/off. Adjust the END POINT/Travel of this channel to control smoke pump flow rate so as to control the smoke density. For more detailed information please see your radio manual.
Specifications:
|
MRC-K-028
$119.99
1/4 Scale Turnbuckles,1/16" (1.5mm) Eye & 4-40 Threaded (2 pcs)
| 1/4 Scale Turnbuckles,1/16" (1.5mm) Eye & 4-40 Threaded (2 pcs) |
vp-acc02
$15.99
