GT Power Aircraft Navigation Lighting System
Description: GT Power Aircraft Navigation Lighting SystemThis lighting set is a step up from the GT Power Aircraft Lighting System and ontains a control board that simulates actual aircraft navigation lighting. The system has been designed according to real aircraft navigation lighting standards featuring beacon, navigation and strobe lights to make your aircraft look more realistic. A great way to add a level of scale realism to your models and it is extremely easy to install. Using long life, super-bright (3 & 5mm diameter) LEDs, you will not have any trouble seeing any model they are installed in! All LEDs or LED combinations have separate plugs so they can be moved around for different lighting combinations. The system can be powered from your receiver or a separate power source and is suitable for any mid-size airplane (up to .60 size) or helicopter. The kit consists of eight bright LED lights, a control board with power lead, and clamps for securing the LEDs to the fuselage and wings of your aircraft, as well as double-sided tape for securing the control board within the fuselage. The included lights and patterns are as follows:
The control board power lead features a male JR plug for connection to any open channel on the receiver. We suggest using a UBEC or receiver battery pack to provide adequate power to these lights, as the standard linear mode BEC on most ESCs may become overloaded. Another option is to use an ESC that has a switch-mode BEC. FEATURES:
SPECIFICATIONS:
|
Bob Smith Industries Insta-Cure+ Gap Filling CA
| Untitled Document Description:Bob Smith Industries CA Glue Insta-Cure+™ Super Glue, CAInsta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. Directions:Unscrew top from nozzle. For finer applications, use the extender tip. Apply Insta-Cure+™ CA to one side of the parts being joined, then hold them tightly together for 5-15 seconds. For larger bonding areas, apply serpentine beads of the CA with enough spacing to allow for the spreading of the adhesive. Insta-Set™ accelerator can be sprayed to cure the CA that oozes from joints. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220° F. Soak extender tip in acetone for cleaning
Works Best On:
Works Good On:
Avaliable in 2oz and 3/4 Pocket Size. Pocket CAs feature a new top that has a pin built into the cap that covers the nozzle. This pin seals the bottle so that if it is tipped over, the bottle will not leak. This makes the Pocket CAs ideal for keeping in your tool or field box, just like our IC-Gel. One disadvantage that the new Pocket CA top has is the bluntness of the nozzle. This makes it more difficult to apply small amounts of the CA, especially in tight places. From the feedback we have received, it appears about 25-30% of users prefer the new Pocket CA top, which means that over 70% prefer our standard top for general bonding purposes. Most users are buying both types. Our original top for the workshop, and the Pocket CA for use out in the field. The 3/4 oz. Pocket CAs are available in BSI's Insta-Cure, Insta-Cure+, Maxi-Cure and Super-Gold+. BSI's new extender tip #304 works on the Pocket CA.
Click to Download Safety Data Sheet
|
BSI-CA-56b908caadc59
$4.99
Spot On Cap Bolt Washers
| High quality cap bolt washers. Available in two sizes that can fit M3/ #4-40 threads or M4/#8-32 threads |
SPO-WACB-
$8.99
30cc Piper Cub - Yellow
| The J3 92" Piper Cub is an amazing aircraft for smooth flights and a very scale appearance. The 30cc Piper Cub form RedwingRC has a beautiful color scheme that helps with orientation and leaves you plenty of room for custom graphics. The 30cc Piper Cub is built with high quality balsawood and provides a lightweight airframe that is ridged and strong in all the right places. The 30cc Piper Cub was made to be an outstanding aircraft. The large rudder, large control surfaces, and aerodynamic nose makes this a very responsive plane in the air. As with all RedwingRC planes, the 30cc Piper Cub has quality hardware and is a fun build. Enjoy the sky with the 30cc J3 Piper Cub available at RedwingRC!!!
Features:
We DO ship our planes internationally!
Please contact us with your location for more specific cost.
| ||||||||||
30-J3Cub-Y
$399.00
