Fokker D. VII Scale German WWI Fighter Biplane (Giant Wingspan 82.7" 2100mm)
The Fokker D.VII was a German World War I fighter aircraft designed by Reinhold Platz of the Fokker-Flugzeugwerke. Germany produced around 3,300 D.VII aircraft in the second half of 1918. In service with the Luftstreitkräfte, the D.VII quickly proved itself to be a formidable aircraft. The Armistice ending the war specifically required Germany to surrender all D.VIIs to the Allies. Surviving aircraft saw much service with many countries in the years after World War I. Specifications:
Recommend Equipment:
Note: Vintage wheels & Dummy guns/engine not included in the kit but can be purchased in drop down menus above. Kit Features:
Note: KIT version does not include any electronic device.
|
Brass Collet with Tension Screw (10 pcs)
| Brass Collet with Tension Screw |
VP-ACCO1-Brass-Collet
$17.99
CNC Steel Turnbuckle (Tension Regulator) (10 pcs)
| CNC Steel Turnbuckle Tension Regulator (10 pcs) |
VP-ACC02-Tension-Regulator
$29.99
RCEXL Pro Smoke Pump System
| RCexl Pro Smoke Pump System
Introducing the Red Miracle Brushless Motor Smoke Pump! These light weight pumps have a CNC processed 6061 case with a Japanese high speed oil seal. The brushless motor/ESC supply smooth transmission and helps avoid the possibility of a spark. Basic Set up:First connect the pump to the ESC, fuel filters, muffler and smoke tank (drawing included to help with this).Plug your radio connector into the switched channel (such as landing gear or flaps). Turn on radio, make sure switch is off (100% negative) for at least 5 seconds and turn on. If the pump pushes fluid toward the muffler, the set up is correct. If it tries to pump toward the tank, please change any two wires' connection of the three wires connect the brushless motor and ESC. Radio Set up:3. Non programmable Radios Use a switched channel to switch the Smoke pump on and off. Since there is no trim control on a switched channel, the flow rate is consistent. When the switch is on, flow will be at maximum. We can set the END POINT/ATV of radio switch channel to control the maximum flow rate so as to control the smoke density. 4. Programmable Radios Plug the smoke signal wire into a spare channel (such as the 8th channel). Set this channel program mixing the Throttle channel, then set a switch for programming mixing on/off to control smoke pump on/off. Adjust the END POINT/Travel of this channel to control smoke pump flow rate so as to control the smoke density. For more detailed information please see your radio manual.
Specifications:
|
rcexl-PRO Smoke
$39.99
Hobbywing 3A Power Regulator 5/6V UBEC (2-6S Input)
| Hobbywing 3A Power Regulator 5/6V UBEC (2-6S Input)
Description: GT Power Servo Consistency Master. With this cool device you can test up to 3 servos at a time for consistency and precision. With the GT Power servo tester you can see how servos react in three different testing modes. Manual, Neutral, and Automatic. --- Manual Mode:: Turn the knob at different speeds however you want to check reaction time. Neutral Mode:: Make the servo go back to the neutral position. Automatic Mode:: "window wiper mode"- make the servo swing back and fourth at max angle. --- Specs:
|
QX-10788-HW-3A-UBEC
$7.99
Dynam DHC-2 Beaver V2 Red 4S Sea/Land Float Plane 1.5m (59") w/ Flaps Plus Floats & Rubber Wheels
| Dynam DHC-2 Beaver V2 Red 4S Sea/Land RC Float Plane 1.5m w/ Flaps Plus Floats & Rubber Wheel *Free shipping is for continental US only RedwingRC Plug-and-Play aircraft! Attention scale seaplane enthusiast!!! The Dynam Beaver is a must have because of its ease of flight, scale appearance, and durability. This seaplane has incredible flight at slow speeds because of its perfected design. The Dynam Beaver comes with a pre-painted finish from the factory and even includes pre-installed LEDs!!! We recommend a LED driver to really get the LEDS to shine bright, a LED driver must be installed to maximize the full potential of the LEDS. Hey don't worry, the Dynam Beaver wont only land on water. Landing gears are included so you have the option of installing the floats or the landing gear with wheels. The Dynam Beaver is flap ready. The wings have the cutouts for the servos and hinges. You will need to supply the servos and servo reverse (if your radio does not have this feature) Build time is around 45- 60 min from box to air. Expect flight time to be from 8-15 minutes, but all depends how fast you fly.
Key Features:
Specifications:
|
DY8961-beaver-red
$249.00
