BMS-591SG, LARGE OFF-ROAD MONSTER TRUCK ROCK CRAWLER HV-DIGITAL, MEGA TORQUE, HIGH SPEED, CORELESS +Servo Arm (55.1kg/765.3oz, 0.10sec at 8.4V)

Our Price:

$102.99

Quantity (10)

BMS-591SG, LARGE OFF-ROAD MONSTER TRUCK ROCK CRAWLER HV-DIGITAL, MEGA TORQUE, HIGH SPEED, CORELESS +Servo Arm (55.1kg/765.3oz, 0.10sec at 8.4V)

Large Servo, Ideal for 1/6 ~ 1/8th Short Course, Buggy ( Off-Road ), GT ( On-road ), Monster Truck, Rock Crawler

Soft Start Protection	Soft start to a neutral position.
Over Voltage Protection	Over 9.0V drive the protection mode and 8.4V return to normal mode.
Low Voltage Protection	Lower than 4.0V, drive the protection mode and 4.5V return to normal mode.
Locked Rotor Protection	Stall in 5 sec, output torque goes down.
Temperature Protection	Overheat 85 degrees C (185 degrees F), drive the protection mode and down 75 degrees C (167 degrees F) return to normal mode.
Lose Control Protection	When losing the transmitter signal, that servo will be back to the neutral position immediately and lock.

Operating Voltage Range

4.5V ~ 8.7V ( 2S Li-Fe & HV Li-Poly Compatible )

Control System	32-bits CPU Digital Calculator / AD 12-Bits Resolution ( 4096 Steps ) Frequency：Up to 333Hz & Neutral：1500us or 1520us
Dead Band Width	0.002ms ( Default：2us)

Ball Bearing	Dual, Stronger Ball Bearings
Gear	Stainless Steel Output Gear With All Matel Gears
Motor	High-Efficiency Coreless Motor
Outside Case	Middle: Aluminum Alloy Case W/ Upper & Bottom: Industrial Plastic Cases
Horn / Gear Spline	15 Teeth ( Universal Type )
Connected Cable Length	300 mm (11.81 in)

Dimension (mm)	59.7 x 29.6 x 54.6 mm / 2.35 x 1.16 x 2.15 in
Weight (gram)	168.5 ± 1 grams / 5.94 oz
Product Picture / Dimension Sketch

Includes Servo and Servo Arm

Description:

Type:	DSMX Compatible Full Range Receiver
Number of Channel:	6
Modulation:	DSMX Compatible (Also DSM2 backward Compatible)
Band:	2.4 GHz
Dimension:	25(L) x 18(W) x 11(H) mm
Weight:	4.5 grams + 2.5 grams
Voltage Range:	3.45 - 8.4 V

Highlight
- FailSafe for all channels via press of a button
- DSMX Satellite port

Understanding the receiver

Setup Instruction

Binding

Plug bind plug to the receiver.
Provide power to the unit. LED flashes quickly.
Enable bind mode in transmitter and ensure distance separation of 2 meters from receiver. Solid LED light means binding is completed.
Remove bind plug.

Setting Failsafe

Start by binding the receiver to the transmitter in the normal way and proceed as follows to set failsafe
Ensure that transmitter and receiver are turned on.
Insert bind plug into the receiver (Note: to set failsafe, bind plug is applied only when the receiver is turned on).
Set transmitter controls to the desired failsafe positions.
Press the side pushbutton to memorize failsafe settings.
Observe that the green light at the end of the receiver turns on to indicate failsafe is set. (Repeat step 4 will cause the LED to turn off which means failsafe is disabled).
Remove bind plug.
Disconnect the power for at least 2 seconds and then reconnect the power again. Test failsafe by turning off the transmitter.