Heat Shrink Covering

Contact UsCustomer Reviews

Heat Shrink Covering

Our Price:

$2.00

Color
Quantity (30)

Availability 30 in stock
Weight 0.80 lbs
SKU DW-Solid Green

Heat shrink covering for RC planes

This covering is a high tech polyester covering that is sensative to heat which makes it easy to apply to your plane. It offers high adhesion, fuel proof/waterproof covering for your plane. Easy to apply using a heat gun and/or iron.

:Specs:

  • Width: 23.5”
  • Temp to adhesion: Approximately 250 degrees F
  • Shrinkage begins: Approximately 275 degrees F
  • Maximum recommended temp: Approximately 300 degrees F


For instructions on how to apply covering here is a helpful tutorial:

http://www.rc-airplane-advisor.com/heat-shrink-covering.html


Sold in 1 Foot Sections. Please select how many feet you want. Ships in Prioirty Mail tube.


: *
: *
: *
 

Bob Smith Industries Foam-Cure

Untitled Document

Description:

Bob Smith Industries Foam Cure

Foam-Cure™

FOAM-CURE™ is a silicone based adhesive that works very well on EPP and EPO foams. It is crystal clear and cures to a more flexible consistency than CA. It is, however, not instant bonding like CA and there is no accelerator to speed it’s curing. To obtain a faster initial bond when bonding two pieces, FOAM-CURE™ can be applied to one piece and after the two are joined, they can then be pulled apart. After letting it air dry for about ten minutes, FOAM-CURE™ will act like a contact cement when the parts are rejoined, resulting in enough tack strength to allow the next steps of assembly. Full strength is reached in 10-12 hours.

FOAM-CURE™ works with all foams, and will actually bond most other materials. It will bond wood and plastic to foam, and is a good canopy glue. FOAM-CURE™ does not, however, cure flexible enough to act as a hinge for aircraft control surfaces. Its limitations occur when bonding large areas of two non-porous materials. FOAM-CURE™ requires exposure to air for drying. If one tried to bond, for example, a half-dollar coin to glass, over 90% of the adhesive would never cure, since the solvent it contains would have no where to evaporate. A small amount of denatured alcohol can be mixed into the Foam-Cure to make it thinner.

 

Works Best On:

  • EPP Foam
  • EOP Foam
  • Clear Canopy
  • Paper and Crafts

 

Cut off tip of nozzle. Apply to one part before joining. Use tape to hold parts in place during cure. For faster curing, pull the joint apart and let Foam-Cure™ air dry for 5-10 min before rejoining the parts. This results in enough tack strength to allow the next steps of assembly. Full cure takes 10-12 hours. Foam-Cure™ works on all foams, especially on EPP and EPO, and will bond a porous surface to non-porous materials. Foam-Cure™ is also an excellent glue for clear canopies, and will also bond paper. If needed, denatured alcohol can be used to thin or clean up uncured Foam-Cure™. Replace cap after use.

 

Click to Download Safety Data Sheet

 

BSI-AC

$2.99

Heavy Duty Switch - with LED and Charge Jack

Heavy Duty Switch - with LED and Charge Jack 

SW-LED

$9.99

Heat Shrink Transparent Covering

Heat Shrink Transparent Covering for RC planes

Please contact us for information on if your plane is using Ultracote, or TruCote before ordering if you are unsure

Description:
TruCote covering is a high tech polyester covering that is sensative to heat which makes it easy to apply to your plane. It offers high adhesion, fuel proof/waterproof covering for your plane. Easy to apply using a heat gun and/or iron.

  • Specs:
  • Width: 23.5”
  • Temp to adhesion: Approximately 250 degrees F
  • Shrinkage begins: Approximately 275 degrees F
  • Maximum recommended temp: Approximately 300 degrees F


For instructions on how to apply covering here is a helpful tutorial:

http://www.rc-airplane-advisor.com/heat-shrink-covering.html


Sold in 1 Foot Sections. Please select how many feet you want.

Please put what plane this is for at checkout so that we can match it!

DW-Transparent Film

$2.00