55A ESC with Heat Sink BEC
55A ESC with Heat Sink BEC, Suitable for 2S-5S Airplane, Glider or HeliFEATURES:
SPECIFICATIONS: Size: 88 x 29 x 13 mm Weight: 51.5 g Max Continuous Current: 55 Amps Operating Voltage Range: 6 to 15V On Resistance: 1.56 mOHM Max BEC Output: 4 Amps @ 5.0V 2S~5S Lithium, 6~19 Cell Ni, with Heat Sink
DETAILS: Watt-out-put limit: The output is rated at 388 watts. Under this watt, the speed controller will work normally. When the wattage reaches approximately 410~420, it will automatically shutdown to prevent the speed controller from overloading. Temperature protection: When the temperature reaches 95 degrees C, the speed controller will slowdown and the output will reduce to 50% and the on board LED will turn on. You must move the throttle stick to idle position to reset the speed controller and will work once you throttle up again. Warning: DO NOT install a motor which rating is larger than the speed control’s limit to avoid damage or burn down.
|
HiTec 7245 MH
The PERFECT 30cc Dual Elevator Servo |
HS-7245 MH
$75.99
Bob Smith Industries Insta-Cure+ Gap Filling CA
Untitled Document Description:Bob Smith Industries CA Glue Insta-Cure+™ Super Glue, CAInsta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. Directions:Unscrew top from nozzle. For finer applications, use the extender tip. Apply Insta-Cure+™ CA to one side of the parts being joined, then hold them tightly together for 5-15 seconds. For larger bonding areas, apply serpentine beads of the CA with enough spacing to allow for the spreading of the adhesive. Insta-Set™ accelerator can be sprayed to cure the CA that oozes from joints. Full strength is reached in three hours. Wipe the nozzle clean before replacing screw-on top. Refrigerate to extend shelf life. Cured CA is stable from -40 to 220° F. Soak extender tip in acetone for cleaning
Works Best On:
Works Good On:
Avaliable in 2oz and 3/4 Pocket Size. Pocket CAs feature a new top that has a pin built into the cap that covers the nozzle. This pin seals the bottle so that if it is tipped over, the bottle will not leak. This makes the Pocket CAs ideal for keeping in your tool or field box, just like our IC-Gel. One disadvantage that the new Pocket CA top has is the bluntness of the nozzle. This makes it more difficult to apply small amounts of the CA, especially in tight places. From the feedback we have received, it appears about 25-30% of users prefer the new Pocket CA top, which means that over 70% prefer our standard top for general bonding purposes. Most users are buying both types. Our original top for the workshop, and the Pocket CA for use out in the field. The 3/4 oz. Pocket CAs are available in BSI's Insta-Cure, Insta-Cure+, Maxi-Cure and Super-Gold+. BSI's new extender tip #304 works on the Pocket CA.
Click to Download Safety Data Sheet
|
BSI-CA-56b908caadc59
$4.99
BMS-A10 MICRO, HORIZONTAL MOUNT, HV-DIGITAL, F3K
BMS-A10 MICRO, HORIZONTAL MOUNT, HV-DIGITAL, F3K |
BBR-BMS-A10V (horizontal)
$46.99